Hi all , just wondering if anyone has come across the BHC 4050i backing up around where the waste from the transfer belt to the waste toner bottle? I have one that had this , so i was able to remove...
Type: Posts; User: razzer
Hi all , just wondering if anyone has come across the BHC 4050i backing up around where the waste from the transfer belt to the waste toner bottle? I have one that had this , so i was able to remove...
Oh yea , that one , gotta wonder what that actually even does , as the papers run under those silver idler brackets and rollers , i mean it is there for some purpose. I know some guys have replaced...
Directly behind the sponge rollers looking in from the open black door there is this guide with those mylars on it , this is the guide i mean. The guide itself is up a little bit , so mostly when...
Hi , thanks , is this mylar literally on the bottom of the path , past the sponge rollers , or is it on a guide that has several mylars on it that hang down?
Anything on a EAB0 error in saddle stitch , paper all mangled up ?
Hi , just wondering if there is anything common that causes pages to be mangled up and all crooked and sometimes jamming or coming out bunched up and incorrectly folded in the saddle stitch section...
Hi all , went out to look at an old HP M712 printer that was randomly bending some corners , i went to take the fuser out , which is not complicated , as you release that latch from the left door and...
Whatever it is , i seen it several times already.
I too have seen this and replaced the drum and it came back, so i cleaned it off the drum and charge roller. Does anyone know how long this lasts if you clean it off? Also , is the bulletin saying...
Yea we just started working on Kyocera's and i have this very intermittent code. But when i look in the DF 470 parts manual , it doesn't list the sensor as " Belt Sensor" or the solenoid as " Belt...
Any basic issues with the HP 4200 showing offline. I have not been there yet , but they say there is no connection lights. Maybe formatter (or with this model , could still be jet direct card?)....
Sometimes you have to replace the fuser itself. But if it is only several months in between , thats not terribly bad.
Yea you can swap them , but there is the chance of issues if the life is low especially on what you are putting in.
Is that exactly what it says in the scan logs in top access? Anyway it sounds like an issue with their SMTP server , or reaching it on the network. Are they using some kind of internal exchange...
Well it seems like it is jogging the staples forward, I mean it sounds like it . I did order a board and am gonna also get the harnesses there too.
Also got the above mentioned issue and all seems good with the staples and staple cartridge and the holders as well. Rest of finisher and machine works.If staple cartridges are removed the message...
Hi , so i got a Toshiba 357 that jams around entering the fuser and gives E010. So there is a grind as it stops , , and it seems like the trailing edge is folded as though maybe the registration kept...
was it comming out crooked from the tray then? getting hung in fuser?
don't know , it seems odd that it would work fine on another machine. maybe pinched wires on the harness running back to the system board?
i had this the other day and it was the registration clutch. it was the first time i saw it ever do that amongst the myriad of other issues ive seen it do. when the jam occurs does the print shift?...
thanks for replies. anyway i cleaned out all inside the guides and plates on the feed side and replaced the reg sensor , upper and lower drawer feed sensors(these are more like transport sensors to...
hello all. been a while since i have been on. having issues though with a 2830c , E061 and E062 codes from the 2 upper trays(size settings are correct). this machine has the two cassettes and a KD...
if you run some monocolor prints are all colors affected?
did you try to adjust finisher height?possible inlet guide is warped?
hi all, came across an ES 453 that something like 500,000 or better showing for a dev count. so changed it and did 05-200 and everything went well. couple hours later they called with an install new...