Search:

Type: Posts; User: splblazer91

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: Konica c227 with the error (99-01) ONLY happening from tray 1

    Had one like this last year. Ended up being Tray 1 lift motor.
  2. Replies
    4
    Views
    629

    Re: Replenish toner message Bizhub C754e

    Make sure the pins that the toner bottle pushes against arent bent. Next Step would be Toner Sub Hopper.
  3. Thread: KM C754

    by splblazer91
    Replies
    13
    Views
    1,457

    Re: KM C754

    2 bars is alwayss HDD oe SSD
  4. Re: SERVICE MODE BIZHUB C554e unable to enter

    A lot of these machines are starting to have issues with SSD boards. Bad ssd board wont allow you into service mode and there are very few boards left. These machines are end of life.
  5. Replies
    7
    Views
    750

    Re: FS-539 eject claw

    30 min job if you have the right size prybar :D
  6. Replies
    12
    Views
    2,762

    Re: C450i Colour Drums

    Replacing an i series color drum with an i series black drum or vice versa.
  7. Replies
    12
    Views
    2,762

    Re: C450i Colour Drums

    I havent had luck with swapping i-series drums. They always seem to background.
  8. Replies
    2
    Views
    547

    Re: p errors on KM

    Gotta replace with new parts or the P codes wont go away.
  9. Re: Konica Minolta bizhub 368E jamming on side

    3205 is always the fuser or fuser drive assy. Do you see brown dust (rust) near the back of the fuser? If so, replace drive assy.
  10. Replies
    3
    Views
    539

    458 Protocol Errors

    Knowledge Base was no help. Have Changed multiple settings in SM to no avail. Initalized fax as well.
    Can send all day long just fine. When receiving a multii page fax it will usually fail halfway...
  11. Replies
    3
    Views
    771

    Re: Bizhub 658e

    Paper Feed Drive Assy
  12. Replies
    7
    Views
    1,004

    Re: BH 1100 Slow Printing

    FIXED!
    Replaced Controller today with no luck. Tech Support was no help so I started searching KB Articles. Found one for the 8 series. It had me go into the driver and turn off auto obtain...
  13. Replies
    7
    Views
    1,004

    Re: BH 1100 Slow Printing

    There arent initialization settings on an 1100 like there are on the office devices. I did the controller hdd format which wipes the network settings though.
  14. Replies
    7
    Views
    1,004

    BH 1100 Slow Printing

    They have 2 machines. Only one is messing up. Does it with crossover from my laptop as well. It is slow to print and takes about 30 seconds to pull up the printer preferences. Web Interface is also...
  15. [Error Code] Re: Develop INEO+ 554e/Konica Bizhub C554e - 0.00% TCR-C

    Replace sub hopper
  16. Replies
    1
    Views
    522

    Re: Bizhub C450i FS-539 paper output

    Either high humidity in the environment causing the paper to curl or its gettin caught on the joggers at the exit of the finisher. Try turning down fuser temp first and if that doesnt work its time...
  17. Replies
    1
    Views
    434

    Re: 754e toner in an 808

    The answer is yes. It works. Have to dump it into tn-812 bottle though.
  18. Replies
    42
    Views
    9,160

    [Misc] Re: Toner compatibility

    tn-712(754e) can be dumped into tn812(808) bottles. Take off end cap and there is a plug. just need a funnel.
  19. Replies
    1
    Views
    434

    754e toner in an 808

    Anyone tried this yet? 808 Toner is getting scarce.
  20. Replies
    5
    Views
    1,211

    Re: BH 808 finisher jam 72-18

    Havent seen that yet but I did move the finisher to a different machine and it did the same thing.

    Update: I replaced all the metal and plastic entrance guides as well as the Finisher board. Ran...
  21. Replies
    5
    Views
    1,211

    Re: BH 808 finisher jam 72-18

    Negative. Only about 400k on this one. I did go ahead and remove that mylar though. That thing is useless.
  22. Replies
    5
    Views
    1,211

    BH 808 finisher jam 72-18

    FS-536 finisher. It will run 10-15 pages then jam at the finisher entrance rollers. J code 72-18. It never gets past the entrance rollers when it jams. Anyone seen this?
  23. Replies
    7
    Views
    1,498

    Re: new c257i error c9402

    Yup
  24. Replies
    7
    Views
    1,498

    Re: new c257i error c9402

    Downgrade FW. There are different models of the CCD assy that arent always compatible,
  25. Replies
    2
    Views
    1,086

    Re: Jam 72-17 on BH808

    Very familiar with those problems on the 4e series. This machine however only has 300k on it. Mylars and Jogger guides are good. Its been having this jam since about a month after it went in. I have...
Results 1 to 25 of 204
Page 1 of 9 1 2 3 4