Another customer with the a 3030 called said they have light copies as well.
F6-21 on most of the machines are in between "-37" & "-47", some use OEM toner/druns and some use compatible...
Type: Posts; User: disko
Another customer with the a 3030 called said they have light copies as well.
F6-21 on most of the machines are in between "-37" & "-47", some use OEM toner/druns and some use compatible...
oh, and I have also swapped in a TDC Sensor ( L2DA00000127 ) as well!
Good Friday afternoon!
Having quite a battle with a few machines in the field. the DP-2330/3030 series. Here is the issue, Customer originally called in for Light Copies, PM cycle was close for...
HAHA! I got fed up with it, tried heating it up / cooling it down. Channel locks. even destroyed a pressure roller trying to get it to stay in place so I could turn the knob. In the end, I took a...
Hey thanks, ended up having to hacksaw the shaft off and replacing the screw.
All is well with new parts :)
I have been turning clockwise and it wont budge.
I have 3 fusers that im trying to rebuild. I cannot seem to get the Jam Release knob off the pressure roller on either units. Is there a trick? I looked in the manuals and couldnt figure out a way.
...
Copystar CS 6551ci has magenta banding on the copy output. Attached is a sample. Also, when I put the original on the glass it has bleed on the edges (page 2 of attached PDF).
Machine has around...
Im having the same issue, 3 fuser units now, loud thumping. Just replaced the fuser and 12 hours later.. thump thump thump.
Trying to resolve this with Kyocera tech support is frustrating.
Hey, thanks for the insight, its happens from either tray. I will look for the clutch and replace it. I have replaced the Registration clutch #L9EAAK000008 (2602 in parts manual) I will swap out the...
I am having a issue with a DP-3530, the machine will cut off some of the image, printed or copied.
I have replaced the ADU clutch and LSU. I have attached a pdf with the examples. Its always 1st...
Update; did the transport fix I found here, helped but then started jamming on multiple duplex. Turned out the Intermediate Actuator Flag on the fuser jam door was getting hung up and not returning...
Should be in function -> General Settings -> Key Op "0000" or "00000000" then navigate to IP Settings, I haven't been at these machines in a while.
You should be able to enter the IP address in...
I have a customer who is having issues duplexing. Machine pops a J41 code. Here is what I have done so far, as well as some notes.
Replaced the Transport Unit in the belly of the machine, replaced...
So how would one connect a router from say netgear to the ATT uverse #5168nv model no.
Here is my issue, I have a customer that has AT&T U-Verse and we are installing a Panasoinc dp-8045. It will not show up on network, able to ping or any sort of connectivity.
Have given it a...
Have a machine in the field that is making light copies, very light to be exact. I cleaned the LSU, drum unit (disassemble & clean). I put the density adj on the copy home screen all the way darker...
This is what I thought also, but after a new box of paper, problem came back next day. Ended up rebuilding a whole new fusing unit and direct swapping. More than likely had something to do with...
So I have a client who has a C450 with a de-laminated pressure roller. I have found a few places that has lower pressure rollers for sale but figured I would ask, what is more reliable and better in...
Good morning all, been battling this machine for weeks now. I have come to ask for some backup! ha, The machine is a Panasonic Workio DP-3030 with 260,441 copies (total) on it. I have rebuilt the...
Ill have to check the settings, off the top of my head I am thinking its around -41 / -39 ish. Also yes, F8-09. We use OEM developer but Compatible everything else. I will have to check the settings...
Yes I finally got around to it, been one busy week for being the only technician here!
here are the attachments. notice on the vertical lines.
1st Page - Quantum off
2nd Page - Quantum On...
No powder, cleaned it multiple times. I did a PM since it was 80k past previous service. New developer, Bias Transfer Roller, Bias Charge Roller, Cleaning Roller, Cleaning Blade, Front Cleaning Felt,...
Just wanted to update; Replaced SC-PCB again, from a different parts machine. It did fix the issue. Apparently these go bad often ha.
Thank you for the help!