Set nvm:716-150 = 300 default
Set to 1000 - problem solved
Type: Posts; User: Dech
Set nvm:716-150 = 300 default
Set to 1000 - problem solved
or use Papercut mobile printing... Its free
Free Google Cloud Print alternative - Mobility Print | PaperCut | PaperCut
012-299 Compile No Paper Sensor ON Fail file:///C:/Edoc/common_e2/images/full_a.gifBsd-on:CH16.60file:///C:/Edoc/common_e2/images/description.jpg The Compile Tray No Paper Sensor is not turned ON...
Its your ROS. had this problem. cleaned the ROS. stayed the same. opened the ros and cleaned it agian. same. replaced the ros unit. problem solved..
If the NVM[741-700] (Belt Home Fail Too Long continuous occurrence count) is [3], clear to [0]
Check your draw and main chassis plugs.. I had a few clients slam the draw closed and damaged the plug connectors..50869
Sorry, its been so busy over here.. only get to look in here once in a while.. Driving 20K a month...
Just set it up the same as you would in I.E on win 7 and 10..
You might have to change...
Had this problem: Replaced the CCD assy. fixed the problem...
I replaced my IOT pwb witch fixed my 041-346
IOT F3 Fuse is blown out.
ProcedureSeeing Wire Network 7.2.1.28, check the +24VDC lines to the following parts for a short:
1ST BTR Retract Motor(PL 6.4)
2ND BTR Motor(PL 3.4)
CC...
For a C Finisher
The Stacker Tray rose to an abnormal height beyond the defined upper limit (Stack Height).
Cause/SolutionCheck the following:
Malfunction of the Stacker Motor...
FOR A D FINISHER
After the Stacker Tray has started rising, the Mix Stack Sensor turned ON.
ProcedureEnter the Diag Mode, input DC330[012-142] (Mix Stack Sensor) and turn it ON. Turn the sensor...
Just loaded windows 11
Just run it in I.E mode in edge..( default browser) set up a xml file with all the i.e roots, add it to group policy then share with i.e
Add the roots to the docs, so...
Remove the whole btr -duplex draw. the two plugs at the back of the draw, that push into the plugs on the machine frame. the bottom one has been damaged, replace the plug..... Make sure there is no...
048-318: IFM/ICM Fan 1/2 Fail
IFM/ICM Fan 1/2 (DC330[048-016])
49793
Check your ribbon cables to the ros (lazer) unit.
If the toner is blocked, it blows F10 fuse on the iot Pwb and the toner motor sometimes burns its brushes. if this happens replace iot and motor... Check the seal on the inner cover( the toner falls...
I've had( look at the attachment, no 9) a tooth break on the no 9(link guide assy) in attachment. Its a black slider shaft that engages the colour dev units. Or the clutch in the no 2 ( main drive...
Does your cyan toner cartridge feed motor run?
If not, check your F3 on your paper handling (iot) pwb... it could be blown...
45333
Australia machines have the software keys in the hideaway hole in the tray, not sure were you store yours. If we loose ours, we get them from our web portal...
044-383 PH F3 Fuse Fail file:///C:/Edoc/common_e2/images/full_a.gif file:///C:/Edoc/common_e2/images/memo.gifBsd-on:CH1.14, CH1.6, CH9.19file:///C:/Edoc/common_e2/images/description.jpg Fuse3 on the...
Its your BP Pwb. as in attachment
094-321 1ST BTR Contact FailThe 1ST BTR Cont/Ret Sensor has not detected Contact(H) the specified time (2400ms) after the start of the operation of contacting the 1ST BTR.
Initial-action
Check...
093-314 Dispense Broken Y
The system detected that the Dispenser is damaged.
The Dispenser Y motor has got damaged- replace the dispenser motor and reset ( test the fuse on the IOT Pwb and make...