Search:

Type: Posts; User: yasir

Search: Search took 0.03 seconds.

  1. Replies
    10
    Views
    1,383

    Re: how to install a new copier ricoh 7502

    yes this the case there is some plastic and tapes near the ibt ,need to connect the ibt ? or it is already connnected ?
    the default settings are already installed?any need to activate it? all are...
  2. Replies
    10
    Views
    1,383

    Re: how to install a new copier ricoh 7502

    i do not have service manual mind you please put attach for this
  3. Replies
    10
    Views
    1,383

    Re: how to install a new copier ricoh 7502

    i am familiar with xerox ,i think there is plastic near the Ibt belt under the drum just to take the screws?and remove it
    also do we need to write data as defult
  4. Replies
    10
    Views
    1,383

    how to install a new copier ricoh 7502

    how to install a new copier ricoh 7502
  5. Replies
    2
    Views
    501

    Re: document centre 480

    but the battery is solded in the chip and it is not available here
    anyone pass such problem
  6. Replies
    2
    Views
    501

    document centre 480

    document centre 480 with dot on screen say communucation error put off and on did nothing the chip that have the yellow battery
    causes this problem
  7. Thread: ricoh 5000&4000

    by yasir
    Replies
    10
    Views
    1,539

    [CQ] ricoh 5000&4000

    we have this problem in Ricoh 5000 it runs copy quality problem faint or background
    change the developer fixed ,but returns again any setup routine
  8. Replies
    2
    Views
    871

    [CQ] ricoh 5000 runs copy qaulity

    we have the mentioned above problem it runs cQ problems faint ,background ,black copies
    change the developer,cleared but it returns back
  9. Thread: MPC 7501 sc565

    by yasir
    Replies
    3
    Views
    675

    Re: MPC 7501 sc565

    also i have SC 555 with ricoh 7502 every morning ,used to run 58012# cleared but comes next day wonder ?
  10. Replies
    0
    Views
    468

    image disk off line in xerox C90

    this comes after any coping ,the machine says put off,also someone has spoiled the admin Access code from 1111 any we to restore it ?
  11. Replies
    3
    Views
    9,963

    [Error Code] error code in ricoh 7502 Sc 555

    the mentioned code comes daily we reset every day can any one help in this issue?
    if we replace the thremister the code cleared?
    yasirmohmed@yahoo.com
  12. Replies
    0
    Views
    389

    how to restore the admin code for xerox c90

    hi gentle men can any help in this issue some guy has changed the default pass word from 1111 to unknow any to restore it
    can it enter service mode without Pws ,
    send your support to...
  13. Replies
    9
    Views
    2,854

    hi please send your price ,yasirmohmed@yahoo.com

    hi please send your price ,yasirmohmed@yahoo.com
  14. RE 470

    I think yr problem in the iverter module check the sensors, see the colour of the sensor eye if it is yellow sensor ok, if brown sensor is faulty
    regds,yasirmohmed@yahoo.com
  15. Replies
    2
    Views
    948

    hi if you finisher slide out open the left cover...

    hi if you finisher slide out open the left cover & check the fuser roll if it is hot or not if not you have to reset the machine via entering diag #11
    50-20 change from 1to 0
  16. Replies
    5
    Views
    3,777

    change the copy cartridge

    change the copy cartridge or also remove the black papers on the erase lamp.
    ote=suckis;10595]When tha console displays the U7 code, press the"zero" (0). If "one" (1) appears then 100% you will...
  17. Replies
    5
    Views
    8,303

    dc440 error code 4o11

    this kind of faults occare due to bad sectors if possible replace the hard desk or remove these bad sectors,good luck
  18. Thread: xerox 5328

    by yasir
    Replies
    3
    Views
    1,625

    u9-3 (is exposure lamp&Ac driver pwb) also optical fuse

    check the above mentioned parts always the mentioned parts cause U9 codes check these parts also if they are ok use simlation mode To Reset as press hold zero button while powering on the...
  19. Replies
    2
    Views
    1,523

    fault codes 3- are communication errors

    these codes are communication errors check if the exposure lamp lights during copying or not also check the scanner home sensor
Results 1 to 19 of 19