This error came up on my MFP. Manual says it's either the low voltage power supply or the system board. I don't want to pay for system board at all. I May be willing to spend a couple hundred bucks...
Type: Posts; User: oldschool
This error came up on my MFP. Manual says it's either the low voltage power supply or the system board. I don't want to pay for system board at all. I May be willing to spend a couple hundred bucks...
It can also be set in U204. It has been reported to me that newer Kyocera models have a coin vendor option in U204 as well as a key counter option. I believe it just changes the message to "Insert...
To give a bit more detail. A kyocera can be vended for copies. We do this by using U206 rather than U204. A patron can send a private print, pay for it and release it. However the Kyocera does not...
I know secure (private) prints can be set up in the driver but a customer asked me if the machine could be set up to reject all print jobs other than secure prints. I've seen this setting with other...
When you say you disabled the coin unit, did you disable it in the SP 5113 service mode? An issue with Ricoh models, The service mode for default optional counter type has two options similarly...
Actually when using a coin op, Key Counter I/F Vendor is used. Konica Minolta engineering clued me in on this. If just key counter is used with a coin box the copier will jam when funds run out....
Pins 1 and 2 are correct. Do not short any other pins together. Pins three and four are for the count. Pin four will drop low and allow the copier to send a 24 volt pulse to the counter. You've tried...
The 20 pin M12 connection outputs level signals for paper size. There are 4 lines that go high or low. Depending on that combination, a vend device can determine what paper size has been selected.
...
SP5-113 set to option 4 (coin rack) for default optional counter type.
User tools > System settings > administrator > (sometimes key-op tools) external charge unit management. Highlight what is...
I let the customer know.
Thanks for the reply!
A co worker said I should have mentioned that you don't need a vend station attached to test this. I didn't think I needed to but it gives me a reason to bump this. ;)
I do not have access to this machine but a customer has asked me a question. Basically when the copier is in vendor 2 mode with scanning is set so that it is not controlled by the vendor, can...
Depending on the type of vending you may be able to disable it in the admin mode. If Vendor 2 was used, Log in as admin. Go to security > Function Management settings (or management function...
I will assume this is our EnvisionWare version of the model 9557 please correct me if I'm wrong (6 buttons on the Jamex main board). I doubt this is a copier issue. A Kyocera can not cause a vend...
I agree there are some rollers that can't be helped. My situation was a large territory and I needed to keep the customer running. Even on worn out rollers I could usually buy 3 or 4 days. This would...
This reply isn't really specific to this thread but when I was in the field I discovered that "Brasso" cleans feed rollers quite well. I used to carry it to polish drums. We used to use fedron to...
The setting in SP5-113 (default optional counter type) for a key counter connection is usually ext key card deduct option 11. Then in user tools - system settings - Admin, you'll need to highlight...
I did want to mention that the True count uses the Vendor II connection and not the key counter connection as the key counter doesn't really differentiate between color and B/W copies. For a B/W only...
We sell a remote copy counter that is used in a lot of UPS stores. It's called a True Count. It's basically a box with a button to enable the copier and sits next to the cash register. As copies are...
Wow this is an old thread. The information is a bit outdated for newer models. Now a days there is a service mode setting to turn on/off the key counter option. I don't have any details on accessing...
The Key counter interface (analog) on a Konica Minolta will only charge one price. The copier would use the Key Counter I/F Vendor setting when connecting a coin box or it will jam when funds run...
I only have a guess. Are you using a DVEND kit from Sharp. I've taken several calls that turned out to be a poor connection in the fuse holder. this stopped it from providing 24 VDC tot he DVEND kit....
As Synthohol stated, Stop 9 once in service should bring up built in billing mode.
Not relevant to your question but worth mentioning...
For C3350/3850/4050/4750 press 22200 to access billing...
There was a connection on IR advanced Canon models that had separate lines for color but it worked as you've described. If there was only enough money for bw it would only send a charge signal when...
I neglected to note that but if memory serves it was a ES3510C,