Very helpful. Thank you.
Type: Posts; User: rightbrained
Very helpful. Thank you.
I'm looking for more accurate description of sensor location and replacement procedures for my Bizhub c541. Ideally photographs as the diagram from the service manual leaves much to be desired....
I appreciate your patience as I navigate through this. I finally found the correct area.
The first jam that started this was 1710 after that I've gotten 1001 after every print attempt.
From what...
I think I'm getting close. You've been extremely helpful. Not sure if I got the jam codes from the right spot. The following links are to photos of the 5 different screens available. Sorry about the...
Ahh. Got it.
J75-42
J72-24
From bypass, pulls sheet in 1/2" and jams. Still trying to learn how to get to jam codes... path found online doesn't work: utility, stop 00 stop 01. This takes me to option #1 under the utility...
I fired up my C451 Bizhub after 6 months of idleness. The first sheet ran throughout, but the second sheet jammed at the side access panel. Now, it jams from every tray and the bypass tray also....
Bizhub c451 with duplex unit. Running 20# legal size from the bypass tray. As it exits, the paper gets released just a hair too soon and doesn't fully exit the machine causing the sheets to get...
I recently picked up a Bizhub c451 to use at home. I knew when I bought it that it jams from tray 1 and tray 2. Some online searches suggests that there are bad sensors in these drawers. I currently...
Hi,
My Lanier LD 525C gives me toner empty message on the black toner even though it's new or not empty. I simply pull it out and put back in (sometimes tapping the bottle) to fix, but it is very...
43430
I replaced the cyan PCU on my Lanier 525c. This did solve the original CQ issue but now there is this new issue. From this image, did I do something incorrectly or did I miss something? The...
43429
I replaced the cyan PCU and the original blue field issue is resolved. But, as seen in attachment, I have missed something or done something wrong. The white areas are not consistent from...
43382
This blue streak that runs from edge to edge began in the middle of a long run. I've cleaned the rollers and used the cleaning wand. The streak shows even when running a blank page. Starts...
Thank you. I suspected the transfer belt but wanted confirmation. Only paid $50 for the machine. Not sure if investing in a new belt is worthwhile. Does anyone have high recommendation marks for this...
My Lanier problems started by wrinkling pages, eventually reaching the point it was wrinkling every other sheet run through. I tried to fix this issue by cleaning all the rollers with a wet wipe.
...
PRINT to non-glossy stock. Old machine - high page count. Tight guides. Probably worn pickup roller on bypass tray. Trying Slims idea but appreciate other thoughts.
I've had this same issue with other copiers I've owned. Now it is happening on my Lanier LD525C.
When I run 80# cover (for business cards) through the bypass feeder, the image moves around on the...
After years of fighting with a Sharp copier at my home based copy shop, it finally died.
I was able to pick up a Lanier LD525C very cheap ($50!) It even came with an extra set of toner cartridges....
My black developer unit on my Sharp MX 2700n is broken. I cannot find a replacement ANYWHERE (I've looked all over online. My copier is pretty obsolete and parts are extremely difficult to find). I...
2nd transfer roller fine.
I don't understand this. I saved the file as a bitmap image (.tif) instead of a vector image (.eps or .pdf) and the image cleared up. Thoughts???
I don't understand this. I saved the file as a bitmap image (.tif) instead of a vector image (.eps or .pdf) and the image cleared up. Thoughts???
Thank you, no, the pressure levers are not left up.
Thank you, but no, the toner is the same that has been running for some time. Not a new cartridge or refill/
I am running an 11x17 color job on 80# cover stock through the bypass tray. It is set to Heavy paper. I've run this same job on same paper before without issues. I have also tried various weights and...
The files you provided are much appreciated and will help greatly. Your response does give rise to another question. Is there a place I can find the complete manual for my copier so I can maintain...