Search:

Type: Posts; User: bigdaddyooo

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    537

    Re: BP-LC10 phantom jam

    UPDATE........Fairly new. i think 80k on it. We removed it and put another brand new one on and customer has had no issues. We did however bring it back to the shop and ran THOUSANDS through it and...
  2. Re: Sharp BP-70C55 Thin blue line on 2 sided copys and scans

    The BP DSPF uses a different white ref chart than the MX's. Make sure you have the correct one
  3. Replies
    8
    Views
    803

    Re: Cloning the SSD on BP's

    Steve our rep advised us to NOT clone machines any longer. They are seeing a lot of problems with lock up, slow networking etc... if you saw the webinar last week he took a lot of time on this bullet...
  4. Replies
    3
    Views
    537

    BP-LC10 phantom jam

    We have an LC10 that jams for no reason it seems. Took it back to the shop and ran a few thousand with NO jams. Has anyone had any problems with this unit? Codes are LPFD_NL and SL
  5. Replies
    0
    Views
    365

    MX-FN22 saddle skew

    Anyone ever have to adjust the skew of 11x17 after saddle stitch has taken place? When you look at the folded print, the top line of paper doesn't line up at the open end. TYIA
  6. Replies
    2
    Views
    525

    BP-70C series fuser

    Has anyone experienced 1 part of a print not fusing? It's on the rear side of a copy or print. I've torn the fuser apart and found nothing that I can see that would cause it.
  7. BP series AIR PRINT w/user codes OS-17+ gets declined

    Print gets declined now after installing Apple OS-17. Customer uses user codes which get declined now. Any ideas? OBTW an Iphone with OS16 or less works fine.
  8. Replies
    9
    Views
    1,213

    Re: Sharp MX-M465 Overtone

    Did you replace the 560TU or the entire unit? It has a sensor just under the roller that goes kooky once in a while and will cause issues like that.
  9. Replies
    19
    Views
    6,093

    GO TO OTHER THREAD about this Re: F1-22 Error Code

    There is another post about this with a bulletin from Germany and is not here in the states.
  10. Replies
    1
    Views
    574

    UPDATE....mfc9840cdw waste locked CLICKING

    I was told by brother that this part is NLA. great...Im SOL. lol
  11. Replies
    1
    Views
    574

    mfc9840cdw waste locked CLICKING

    Customer put new waste unit in but damage had been done. I need to know if that black coupler is included when ordering the drive unit. The coupler and the gear are mashed up. TYIA
  12. Final UPDATE

    So it was the TC pwb. the original one has an inherent issue as it was sent to Hytec for repair but still displays phenomenon. We ordered a new TC pwb and returned the machine to the field and its...
  13. Replies
    2
    Views
    810

    Re: MX-4071 calibration error

    I've had a few instances where my 46-74 would give errors and 99% of the time it was the DV concentration wasn't good enough causing calibration errors. Maybe swap DV units just to get to see if it...
  14. NEW NEW UPDATE

    ok I said we sent the pwb to Hytec and they repaired it. NO it's really not repaired because I swapped out the TC pwb with one from a brand new machine I'm setting up and ran about 500 dbl sided....
  15. NEW UPDATE Re: Random blue lines top to bottom 4071 and BP's

    Had the TC pwb repaired and ran about 200 after I installed it. BLUE LINES AGAIN!!!!!! Im pissed. Back to square 1.
  16. UPDATE.......Re: Random blue lines top to bottom 4071 and BP's

    Well for shites and grins I tried the TC pwb. VIOLA, fixed and hasn't come back. My DSS says I wouldn't have even thought about that. I did it as this is the only board besides the MFP and PCU I...
  17. Replies
    16
    Views
    2,283

    Re: BP-FN11 code F1-22

    I have. 5 FN11's installed and 3 had F1-22 shortly after install. It's maddening. Then I ask Steve...hey have you heard anything on the FN11's? NOPE...wtf
  18. Random blue lines top to bottom 4071 and BP's

    Has anyone experienced random blue lines top to bottom, even in voided area's. on any machines? It seems to be an electrical issue. Both machines in different parts of town (same company) had a...
  19. Re: MXFX15 no receive but does on another mfp with that phone line

    This was the 1st thing i checked.

    UPDATE the loaner never malfunctioned until we went back with the customers machine. It then also couldn't receive. so 2 FX15's plus a loaner wouldn't work in...
  20. MXFX15 no receive but does on another mfp with that phone line

    I brought the machine back to the shop and used it for 3 days. Never malfunctioned. Dozens of sends and receives. I bring it back to customer and 1st 2 incoming I get an NG0000000 any ideas? YES i...
  21. Replies
    1
    Views
    752

    MFC-L3710CW scanner chatter

    I'm having an issue when turning machine on. if I move the 1st cis it will come back to home but then the motor keeps going causing a chattering noise. I removed the top and and can not for the life...
  22. Thread: E7-03

    by bigdaddyooo
    Replies
    3
    Views
    746

    Re: E7-03

    [I have found 2 MFP-pwb with broken red Msata connections. If you push that red wire down it will break the little "shelf" on the MFP pwb. It then doesn't have a good connection from the HDD hence...
  23. Replies
    3
    Views
    647

    Re: MX-3050N no yellow UPDATE

    I started getting 1/2 yellow from top to bottom so for shits and giggles I replaced the LSU unit and VIOLA....fixed. Thank you guys for the suggestions
  24. Replies
    3
    Views
    647

    MX-3050N no yellow

    Drum is coated with yellow toner when doing a 64-1 pattern 9. I have no transfer from drum to TC1. I have replaced MFP pwb, PCU pwb, TC pwb and TC1 unit. Still having the issue. I swapped Y and M...
  25. Replies
    7
    Views
    748

    Re: BP-NV700 gram weight

    Sir, that is for the BP-NV70BA.........I need the BP-NV700
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4