Search:

Type: Posts; User: EasyRider

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    326

    Re: MX2640N Cyan White Lines

    You could try and clean the laser on Cyan. Clean all of them since you are already there.
    Look at the mag roller on the Cyan DV unit, if it has the same lines, you'll need to redevelop.
    (If it...
  2. Replies
    3
    Views
    549

    Re: Sharp MX-6050V Fuser Gear

    I believe it's discontinued because it's not needed.
    I remove it and the metal one-way.
    Fewer problems is "good-er"

    :cool:
  3. Replies
    10
    Views
    1,182

    Re: Feed Tire Kits

    What is that kit part number for the US? We can't get the NROLR3KITFCZZ here.

    TIA
    :cool:
  4. Replies
    8
    Views
    796

    Re: MX-6201N Major Distortion

    Gently remove the Primary transfer belt unit. Do not shake it or ding that belt!
    Check the white gear on the rear. Turn by hand and see if it slips. It has a screw holding it on.
    If you remove the...
  5. Replies
    420
    Views
    130,106

    Re: Canada is disgusting

    + The Dead South, eh?

    :cool:
  6. Thread: U5-30 Code

    by EasyRider
    Replies
    9
    Views
    2,422

    [Error Code] Re: U5-30 Code

    What mloudy said!
    Paperclips and staples are a big cause of these.
    The paperclip can be very hot to touch, but the board will still function after removing the paperclip!

    :cool:
  7. Re: Reset operator password on Sharp MX 2630.

    Proper procedure is to go thru Sharp. Double tap Home, press lower LEFT on LCD, Press 463/ and follow prompts. Call Sharp on hotline, give them the number from your MX and they'll respond with unlock...
  8. Thread: BP-70C36

    by EasyRider
    Replies
    2
    Views
    579

    Re: BP-70C36

    That model does not come from the factory with a offset motor, you get that with the BP-TU10.
    You might try a offset motor from a MX4071 or similar (or TU10) for a temporary trial.

    :cool:
  9. Replies
    2
    Views
    660

    Re: MX-M4070 reset admin password issue

    Using a thumb-drive, you could do a SIM 56-2 Export Copy HDD from a similar model, I use a MX5141, it doesn't matter.
    Sim 56-2 import HDD to your MX-M4070. Simple, easy, works.

    :cool:
  10. Replies
    3
    Views
    750

    Re: SD Card for Sharp MX-3610N

    For the SD card, use a 4Gb (you only need 4, 32 will work) Sandisc SDHC card. I use the blue.
    As for the program, try "HDD Raw Copy" and make a copy of your card, then copy that to the new card....
  11. Replies
    10
    Views
    1,332

    Re: MX-TU16 shift motor part #

    Same as the upper exit foam. Black foam around the white rollers.
    The problem is the tiny springs that hold the white rollers to the exit unit.
    You'll pull your hair out trying to get them back...
  12. Replies
    10
    Views
    1,332

    Re: MX-TU16 shift motor part #

    Make sure on the exit unit, lower white rollers, have the foam when not using a finisher.
    Not real easy to put them back. We just order new exit unit.

    :cool:
  13. Replies
    3
    Views
    688

    Re: Staple, Staple, MISS! & so on...

    That sounds like a similar issue that the FN9 has when the 2 belts and rollers inside, and 2 exit rollers, are worn.
    I believe these will use the same belts/rollers.
    Not easy in the customers...
  14. Replies
    10
    Views
    1,332

    Re: MX-TU16 shift motor part #

    How about this? RMOTS1067FCPZ

    That is just the motor, not the plate and all the little stuff.
    BP parts guide, page 115 for all that.

    :cool:
  15. Replies
    4
    Views
    1,043

    Re: Sharp mx-5071 leaving black lines

    I have read and re-read this post and I am still going to ask the question. Did you replace/swap the main charge?
    You probably did, but I must ask.

    :cool:
  16. Replies
    12
    Views
    1,443

    Re: MX5140n and MX2640N

    Both will be a ".sfu". "SMB2 TLS 1-2 KRACK Virgo2_Combi_0400R2C0_B" is the latest on the MX5141. "SMB2 TLS 1.2 Aries2_Combi_0600A2I0_B" on the MX2640. You might need to do a emergency update on the...
  17. Replies
    2
    Views
    555

    Re: Sharp fax issue w/VOIP

    TT-050415_1 should be the one you are looking for. Dated May 2015. (G3Fax Over VoIP)

    :cool:
  18. Replies
    8
    Views
    2,794

    Re: MX-4071 maintenance code TA reset?

    It is the "Maintenance counter (Total)". Reset the color and mono maintenance total counters.

    :cool:
  19. Thread: BP-50C26

    by EasyRider
    Replies
    3
    Views
    716

    Re: BP-50C26

    Don't you need a MX-PK13 since it is a option on the 50?

    :cool:
  20. Replies
    2
    Views
    481

    Re: MX5070 drum unit blocking up

    Some idea's from the same problem...
    Waste toner boxes

    :cool:
  21. Replies
    3
    Views
    699

    Re: Waste toner boxes

    I have 2 or 3 units that do what you describe.
    One is at a CBD manufacturing place and they use mostly Yellow, so the yellow gets backed up when the "Prepare waste toner" message has been on for...
  22. Thread: BP-HB701

    by EasyRider
    Replies
    1
    Views
    479

    Re: BP-HB701

    According to this:https://business.sharpusa.com/portals/0/downloads/Literature/BP-70M31_70M36_70M45-Specification-Sheet.pdf
    It's for the Mono mfp's.

    :cool:
  23. Replies
    2
    Views
    614

    Re: MX 4070 dead control panel

    Yes, have seen that. Unfortunately.
    That pesky ribbon cable where it connects to the MFP PWB. It's just... fun sometimes. ;)
    You have to be very careful with that connector. Too many tries and you...
  24. Re: Need help with flat spots on MX-3071 fuser unit.

    Set the Power Save to 45 minutes auto power shutoff. Set "Sleep Mode Power Level" to "Motion Sensor Mode". (will need to reboot)
    Advise customer not to turn off main switch, let the machine control...
  25. Replies
    1
    Views
    362

    Re: MX4140 with replace toner message

    Have you checked the B DV unit for DV pull? DV rollers mixing/turning? Is toner dropping into DV input? Is the drum coated? Might need to change developer.
    Is it Friday yet?

    :cool:
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4