You could try and clean the laser on Cyan. Clean all of them since you are already there.
Look at the mag roller on the Cyan DV unit, if it has the same lines, you'll need to redevelop.
(If it...
Type: Posts; User: EasyRider
You could try and clean the laser on Cyan. Clean all of them since you are already there.
Look at the mag roller on the Cyan DV unit, if it has the same lines, you'll need to redevelop.
(If it...
I believe it's discontinued because it's not needed.
I remove it and the metal one-way.
Fewer problems is "good-er"
:cool:
What is that kit part number for the US? We can't get the NROLR3KITFCZZ here.
TIA
:cool:
Gently remove the Primary transfer belt unit. Do not shake it or ding that belt!
Check the white gear on the rear. Turn by hand and see if it slips. It has a screw holding it on.
If you remove the...
+ The Dead South, eh?
:cool:
What mloudy said!
Paperclips and staples are a big cause of these.
The paperclip can be very hot to touch, but the board will still function after removing the paperclip!
:cool:
Proper procedure is to go thru Sharp. Double tap Home, press lower LEFT on LCD, Press 463/ and follow prompts. Call Sharp on hotline, give them the number from your MX and they'll respond with unlock...
That model does not come from the factory with a offset motor, you get that with the BP-TU10.
You might try a offset motor from a MX4071 or similar (or TU10) for a temporary trial.
:cool:
Using a thumb-drive, you could do a SIM 56-2 Export Copy HDD from a similar model, I use a MX5141, it doesn't matter.
Sim 56-2 import HDD to your MX-M4070. Simple, easy, works.
:cool:
For the SD card, use a 4Gb (you only need 4, 32 will work) Sandisc SDHC card. I use the blue.
As for the program, try "HDD Raw Copy" and make a copy of your card, then copy that to the new card....
Same as the upper exit foam. Black foam around the white rollers.
The problem is the tiny springs that hold the white rollers to the exit unit.
You'll pull your hair out trying to get them back...
Make sure on the exit unit, lower white rollers, have the foam when not using a finisher.
Not real easy to put them back. We just order new exit unit.
:cool:
That sounds like a similar issue that the FN9 has when the 2 belts and rollers inside, and 2 exit rollers, are worn.
I believe these will use the same belts/rollers.
Not easy in the customers...
How about this? RMOTS1067FCPZ
That is just the motor, not the plate and all the little stuff.
BP parts guide, page 115 for all that.
:cool:
I have read and re-read this post and I am still going to ask the question. Did you replace/swap the main charge?
You probably did, but I must ask.
:cool:
Both will be a ".sfu". "SMB2 TLS 1-2 KRACK Virgo2_Combi_0400R2C0_B" is the latest on the MX5141. "SMB2 TLS 1.2 Aries2_Combi_0600A2I0_B" on the MX2640. You might need to do a emergency update on the...
TT-050415_1 should be the one you are looking for. Dated May 2015. (G3Fax Over VoIP)
:cool:
It is the "Maintenance counter (Total)". Reset the color and mono maintenance total counters.
:cool:
Don't you need a MX-PK13 since it is a option on the 50?
:cool:
Some idea's from the same problem...
Waste toner boxes
:cool:
I have 2 or 3 units that do what you describe.
One is at a CBD manufacturing place and they use mostly Yellow, so the yellow gets backed up when the "Prepare waste toner" message has been on for...
According to this:https://business.sharpusa.com/portals/0/downloads/Literature/BP-70M31_70M36_70M45-Specification-Sheet.pdf
It's for the Mono mfp's.
:cool:
Yes, have seen that. Unfortunately.
That pesky ribbon cable where it connects to the MFP PWB. It's just... fun sometimes. ;)
You have to be very careful with that connector. Too many tries and you...
Set the Power Save to 45 minutes auto power shutoff. Set "Sleep Mode Power Level" to "Motion Sensor Mode". (will need to reboot)
Advise customer not to turn off main switch, let the machine control...
Have you checked the B DV unit for DV pull? DV rollers mixing/turning? Is toner dropping into DV input? Is the drum coated? Might need to change developer.
Is it Friday yet?
:cool: