Dear,
When I am setteng ink in the black drum it does not accept same brand of Riso ink.
It shows not acceptable.
Kindly advise me the setting to fix the blue ink in the Riso original black drum.
Type: Posts; User: ravikumarj
Dear,
When I am setteng ink in the black drum it does not accept same brand of Riso ink.
It shows not acceptable.
Kindly advise me the setting to fix the blue ink in the Riso original black drum.
Hope the Master is not reversed?! Check proper direction?
Is that master having image through the thermal head.
Dear All,
My copier detects A3 in Auto document feeder.
Every time, have to select manually to A4, More over most of the time while closing feeder beep sounds as if it is not closed properly.
...
Drum cycling gears are modified in the drum unit. Hv you replaced with new set of gears.? Previously nylon gears. now it is a black gear. pl change all the gears .
Ravi.
Thank you .... I have got through as directed..
Is it to be done, opening the front cover....?
Then WhileI was pressing the reset button Please wait appears no dot .. appears on the side of the screen..
Instead scrambled a[phabets appears.......
Did you notice starter spillage near the gears..Change development unit gears with set of bushes it may worn out.....frequently.
I happened to repalce a new heater Unit in Di 3510.
after replacing getting error code C0521.
In this model there is a small reset swith on the main panel near ON/OFF switch. I ve activated reset...
I happened to repalce a new heater Unit in Di 3510.
after replacing getting error code C0521.
In this model there is a small reset swith on the main panel near ON/OFF switch. I ve activated...
[/QUOTE]
Exactly said JACK
Dear,
KINDLY CONFIRM, STARTER 401 OF MINOLTA EP4000 CAN BE USED IN EP3050 OF MINOLTA WITH SAME 600Gms.:confused:
Thanks for the post.
Yes it is heater section Low fusing temperature..
Normally resetting procedure in Minolta is just open the front door and close or swith OFF and ON But
Bizhub reset procedure...
Remove the paper jam in the heater section, then reset.
Reset procedure...
P * c *
then 14
Then start green button
Excute.
Good Luck.
Thanks for the post, I found there is no obstruction of mylar, I ve already fed thick sheet and cleared the path.
It takes the primary feed then it stops in the glass.
Any sensor can be suspected?...
Kindly let me know the section of the error and remedy
Thanks.
:confused:Kindly help me for the call code?
What is the suspected part and to be done?
Every single original feeds in primary then get jammed.
Any sensor or the board in ADF.
I ve removed, cleaned the feed rollers and sensor.
Kindly help me with solution.
Thanks in advance.
Ravi.
We are 2 staff, One supervisor, one technician
arround 350 copiers with differnt brands like K.Mita/Konica Minolta/Sharp.
Yes, I am technician for the past 26 yrs., My first generation of copiers like EP310 Minolta, and BD704 Toshiba..
I love my job. what more, I ve grown up to service Manager, and Marketing as...
Could you try to reheat the 250GSM blank paper and then copying it?
May be rarely used 250 gsm paper which is moistred.
Is it glossy? or rough surface of 250 gsm?
Good luck again
Ravi.
R u using the correct specified model original toner? R u using fresh paper? Then, hv you changed the developer with fresh toner? pl check and confirm.
Good luck.
I found toner in the ATDC sensor, cleaned Drum unit. now working fine. Many thanks.
I have few copiers of Di 7210, but I never found this kind of symptom that copier warming up indication.
I...
Copier symptom in the panel " Now warming up . Ready to scan":confused:
Heater is getting on and the temperature attaining ready,
for the benefit of doubt interchanged with with good working...
26 th year ..... Started as a Tecnician, Service Engineer, Commercial Engineer, Business Development Manager, Some how I like this Office Automation Field and finally I love to be a Tecnician.
I have observed in the control panel no selection in the middle tray.
Paper Size is indicating.
For the benefit of doubt I have interchanged Paper feeding unit of the middle tray to First...