We’re expanding to the Grand Rapids/Muskegon area and are searching for one or more independent repair techs who are interested in doing subcontracted work. This would be a great opportunity for...
Type: Posts; User: The Copy Man
We’re expanding to the Grand Rapids/Muskegon area and are searching for one or more independent repair techs who are interested in doing subcontracted work. This would be a great opportunity for...
Okay here is the latest: I replaced the tray full sensors (2 eyeball sensors at the top), replaced the finisher control board and the tray lift motor. Still have the same problem. Like I never...
Okay here is the latest: I replaced the tray full sensors (2 eyeball sensors at the top), replaced the finisher control board and the tray lift motor. Still have the same problem. Like I never...
Checked the memory and it's not broken. Cleaned and reseated again, no go. Finally printed an event log and all errors since Oct are fax errors. I reseated the fax card and memory dimm. Seeing how it...
Thanks, is this the Fax memory dim or the dim just to the left of that? Also I do have a Kyocera 3050ci, would the memory dim from this machine work?
Okay here is the latest: Tried disconnecting the hole punch unit; no help. Even cleaned and reconnected all connectors on finisher main board and hole punch board; no help there either. I even...
Okay here is what I did to get them by and so far it seems to be working. I set the low power saver to 1 minute vs 60 minutes. This is so the screen goes to sleep 1 minute after each use forcing the...
Tried disconnecting the PH and no help. Got a used finisher board, tray lift motor and sensor kit coming. We'll see what happens...
Be sure you are using the Kyocera KX print driver. The windows drivers and the like are garbage and cause nothing but printing problems.
Thanks they do have the hole punch unit which they never use. When you say PH unit do you mean the hole punch unit? I'm going today to check top tray status with U241. So if it's always on just...
Thanks, have you had a lot of those red cables go bad? Wonder how hard it is to fish one of those through?
Thanks we sold it used with a low meter so I don't know where it came from but where it's at now is clean, dry and no water (Michigan). I do have a 3050ci, do you know if that's the same Ram?
Kyocera 3551ci with DF-770 finisher tray not lifting; tray stays at the bottom and always says finisher tray full on the display. Upon arrival to the customer it said there was a problem with the...
Kyocera 3551ci display starts distorting then turns white or turns off. Almost looks like it's oscillating. When it does this customer can't use the display. Customer has to power cycle the machine...
So nothing to do with the machine calling for developers then? That's what I was thinking... leaning for toward the PCU board (Main board?)
Steve.
I have a customer with a Sharp MX-3100N getting random toner CRUM chip codes F2.76 and F2.77. Does this during color print runs, jams then throws one of these codes every time (lately the F2.77 more...
Thanks a lot for all the help! I cleaned the TPH and it works great now.
Steve.
Thanks bro, dumb question... where is the TPH located? (Under top right cove where masters load?
Steve.
Ok here is what the test print revealed (Proves Scanner is ok)...
Your thoughts?
Steve.34204
Thanks for the heads up. I downloaded the service manual and didn't find a way to get into service mode... could you walk me through getting into service mode and running these tests? Like to see if...
3416934168
Okay see above for samples of what it is doing...
Steve
RA-4200 getting light streaks about 1/2 inch wide down pages top to bottom. Always in the same spot (doesn't move) down the middle of the pages. I can see it on the master too. Bad Drum? I removed...
Seeking a dependable and trustworthy service tech I can sub contract to handle my Lansing area (and beyond) customers. We service all brands of copiers, printers and fax machines on site. Some of the...