Thanks Guys, the fax LIU was the issue. Removed it and machine came right. Thanks to all
Sent from my SM-G985F using Tapatalk
Type: Posts; User: oombees
Thanks Guys, the fax LIU was the issue. Removed it and machine came right. Thanks to all
Sent from my SM-G985F using Tapatalk
Hi Guys,
I need assistance please. I have a LaserJet M830 which hangs on 4/8 of boot sequence. Formatted HDD, performed partial clear of HDD. Reloaded futuresmart 4 firmware. Then did it all over...
You need to replace the drum chips to reset it back to 100%
Sent from my SM-G985F using Tapatalk
Hi Tom,
As far as I know you can use the duplex fuser. My refurb techs has done a couple of them and also done the opposite, converting simplex to duplex.
You can mail me for instructions at
...
I had the same issue not to long ago. I replaced the heating element as well as all thermistors and this resolved my issue.
Regards
Sent from my SM-G985F using Tapatalk
Values should be listed on the inside of the front cover. You need to remove it to find the values label
Sent from my SM-G985F using Tapatalk
Which model?
Sent from my SM-G985F using Tapatalk
You need to enter service mode and insert the values listed on the inside of the door. When you cleared all you also reset the laser values.
Sent from my SM-G985F using Tapatalk
One of three things you could check.
1. Main Controller 1 and 2
2. HDD
3. Engine Board.
I had at least one of these three go haywire before.
Sent from my SM-G985F using Tapatalk
I had the same problem on an iR42xx series. My clients machine detected A3 when copying from the glass. I replaced the size detection sensor snd that resolved my problem.
Hope it helps
Sent...
Replace the pick up assy.
Sent from my MAR-LX1M using Tapatalk
Hi
Look at your timer settings and make sure Auto Off is disabled
Sent from my MAR-LX1M using Tapatalk
Check FU15 on Engine board. They tend to blow and cause E004https://uploads.tapatalk-cdn.com/20200928/54f42552a34da9c34f93e430b2183b84.jpg
Sent from my MAR-LX1M using Tapatalk
See Attachedhttps://uploads.tapatalk-cdn.com/20200920/b69753eb20f84cfb435f560f5cf2f743.jpg
Sent from my MAR-LX1M using Tapatalk
Replace the primary home position sensor. I have had a few that failed
Sent from my MAR-LX1M using Tapatalk
Hi Guys
I have resolved the issue. The issue was related to the use of wrong printer driver. The client previously used a Ricoh device. I realized the issue was stemming from the driver after I...
Hi Martinlee. Check if there is some spilt toner on top of the dev. These devices sometimes drop toner on top of the dev creating a little heap of toner blocking the laser from striking the drum.
...
Hi All
I have a problem with a Canon iR2530 jamming on duplex. The error log states 010D, 0101 and 0108 but what happens is very strange. The paper will go back into the machine from 2 way unit to...
Hi. I get that. The paper doea not lift all the way to the top. It stops halfway, so when the rollers go down to pick up the paper, it does not touch the paper at all. There is a gap between the...
It goes through all the normal motions to pick up paper but the rollers does not reach the paper as the tray only lifts halfway then stops
Sent from my GT-I9190 using Tapatalk
Yes. I removed them, stripped and cleaned them with no success
Sent from my GT-I9190 using Tapatalk
I know its a weird problem. I've been doing this for nearly 20 years and I am stumped.
Sent from my GT-I9190 using Tapatalk
It detects paper size but the paper does not reach the rollers. So yhe obviously a delay jam occurs as the paper is not picked up
Sent from my GT-I9190 using Tapatalk
Yes
Sent from my GT-I9190 using Tapatalk
Hi. Yes its and Adv model
Sent from my GT-I9190 using Tapatalk