Search:

Type: Posts; User: REGSIS

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    590

    Bizhub C250i poor fixing

    Machine has 20k in total. First toners inside (OEM of course. Paper came out with clean picture but toner is smearing under the fingers (not fixed).
    I raise the fixing temperature in service mode 10...
  2. Replies
    17
    Views
    4,411

    Re: Dead Bizhub C250i after Firmware update Q9

    Dowload NG has nothing to do with FW itself.
    Usually a CPU board is corrupted/bad.
    It should be replaced sooner or later.

    I've installed Q9 on one macchine 2 days ago without any problems.
    But...
  3. [Error Code] Re: Bizhub C244e prompting fault codes C-2558, C-2556, C-2554 & C-2552

    I can confirm this. I did this only couple of times, but it works. It is recommended to stabilaze the image and run gradation adjustment. There should be no issues because TCR sensor is reading the...
  4. Replies
    30
    Views
    9,149

    Re: Bizhub 250i error c-c164

    Diagnostic tool should piont you to the faulty part (CPU board or SSD board). Replace it and update FW (select correct machine model).
    In my case it was a CPU board.
  5. Replies
    3
    Views
    1,067

    Re: konica minolta 195 firmware

    If the machine was OFF for a long period of time this message is shown. In this case you have a chance for recovering.
    You must have installed twain driver for this model (you can prepare it with...
  6. Replies
    17
    Views
    1,363

    Re: Biz458e print failure, blue lights flashing

    If that driver is on KM site then KM should ensure it work without issues.
    It's KM fault definetly, not customers at all.
    But customers and especially ITs should trust service technicians when they...
  7. Replies
    14
    Views
    4,788

    Re: C364 not printing black

    Its function is to release and stop rotation of developing unit at specific time.
    Sponge on solenoid acts as isolator, if it's worn timing is wrong.
    Nothing is broken, solenoid works, all you have...
  8. Replies
    17
    Views
    1,363

    Re: Biz458e print failure, blue lights flashing

    Recenty I had an issue with universal PCL driver. Print with that driver came out OK but it blocked next job in queue.
    IT guy reinstalled PC and didn't pay attention and installed 1st one offered on...
  9. Replies
    7
    Views
    1,341

    Re: konica minolta 306i error c2558

    Bizhub 306i should be bizhub 306 with new control board and operation panel.
    Developer, drum, toner and 90% of parts should be the same as in bizhub 306.
    When you change developer, first you have...
  10. Replies
    0
    Views
    1,601

    MF8550Cdn - paper jam after 3rd page

    Machine always stops after 3rd page when printing or copying more than two pages.
    One page and two pages are printed OK, on both single and double sided print.
    If you set three or more pages it...
  11. Replies
    0
    Views
    436

    HP LJ Pro M102w - print delay

    Hi everyone!
    Few of these printers at customer's sites print one page immediately, but the other pages are printed after delay of 1-2 minutes.
    There's no error on printer, no error in print queue...
  12. Replies
    4
    Views
    484

    Re: C224e color print problem

    If you get solid color output (or even thick vertival bar) of one color that means there's no grid charge apllied on drum or developing charge applied on magnet roller or even both together.

    Toner...
  13. Thread: Dead C364

    by REGSIS
    Replies
    11
    Views
    1,115

    Re: Dead C364

    Did you swap printer control board (right to the MFP board)? It might be dead also!
  14. Replies
    14
    Views
    1,805

    [Jamming] Re: Olivetti d-color MF-254 (=Konica Bizhub xxx?)

    Sensor monitor

    59538
  15. Replies
    10
    Views
    1,687

    [Misc] Re: FS-534 and FS-536

    That info is the answer to my question.
    Thank you!
  16. Replies
    10
    Views
    1,687

    [Misc] Re: FS-534 and FS-536

    You are almost right, but not completely.
    FS-536 is finisher for all B&W 8 series, but not all color models.
    C658, C558, C458 - FS-536
    C368, C308, C258 - FS-534

    Similar aproach is applied to...
  17. Replies
    14
    Views
    1,805

    [Jamming] Re: Olivetti d-color MF-254 (=Konica Bizhub xxx?)

    Hope you got my PM

    PS40 (1st duplex sensor) is activated.
    Possible causes: piece of paper on actuator, broken actuator, spring out of place, faulty sensor.

    For location of PS40, see the...
  18. Replies
    10
    Views
    1,687

    [Misc] Re: FS-534 and FS-536

    Does FS-536(SD) work on bizhub C368 series?
    I have them mounted on C558, but asking just in case.
  19. Replies
    19
    Views
    1,596

    Re: Periodic Maintenance Charts.

    Those are pretty serious machines you have to maintain.
    It is allways a good thing to have spare parts. They will be replaced sooner or later.
    For the fact that you are not a technician, I suggest...
  20. [Misc] Re: DV310 starter - where to buy or equivalent DV # to use?

    You can, but you will probably get dirty background after a while (When old toner comes into dev unit).
    If you intend to stick with TN211 then DV116 is maybe more compatible with dv310 than dv414....
  21. [Misc] Re: DV310 starter - where to buy or equivalent DV # to use?

    What I will do when TN-211 became empty is to replace it with TN-217/TN-414 but before that I will empty dev unit and put DV-411. Also remove toner hopper and vacuum old toner. An old (empty) TN-211...
  22. Replies
    21
    Views
    3,538

    Re: C-360i Color/Black drum swap?

    I think that all drum cylinders are the same and with the same yield. Only the chip and some plastics are different.
    I have seen some DR313K drums lasts up to 180k which is the yield of long life...
  23. Replies
    21
    Views
    3,538

    Re: C-360i Color/Black drum swap?

    I didn't try, but I assume that you can swap drum, blade, charging roller and charger cleaner from new DR-313K to housing of DR-316K/DR-316YMC. Parts should fit, and are definetly cheaper.
  24. Replies
    5
    Views
    595

    Re: C558 CL8 replacement

    I think so.
    But also I also think that it's not the same part number for CL8 as in 4 series. Check parts manual.
  25. Replies
    9
    Views
    1,357

    Re: Banding Brand New C4065

    Customer reported after 50k when the printed a job with a solid purple background.
    It was present at all colours; on K the most.
    Bandings were not as thick as yours.
    I took a K drum from...
Results 1 to 25 of 426
Page 1 of 18 1 2 3 4