check drawer unit connectors on rear machine right side facing from front. have had 4 machines throw this code and every one was a 82xx model ad they all had broken connectors on the either the...
Type: Posts; User: JaysOnTheEDGE
check drawer unit connectors on rear machine right side facing from front. have had 4 machines throw this code and every one was a 82xx model ad they all had broken connectors on the either the...
Good idea to check the fans next to them as well, back story was working on a Pro C7100 it kept throwing SC code every 300-500 copies for the pressure roller cooling fan (I don't remember the exact...
looks almost like the one or more doctor blades have debris on them causing the white voids. drum units could be near end of life.
Whatever you do don't try to force the door open you can break or bend the rotating cam pin that locks the door and then it will really be stuck there is a procedure in the manual that allows you do...
Here are the TCRU manuals for the ProC5300S they have a PDF and HTML even got some videos on the HTML version.
Pro C5300S/C5310S(TCRU) download page
Ricoh finally got it right with this fuser I've done one belt and I had the top half disassembled and the belt off in 10 minutes while following along the manual no special tools need. just your...
Did you come up with a resolution yet? Have a few of these in field, not much goes wring with them but always looking to learn about them whenever I can.
Hopefully you changed or inspected the opposed roller on the ITB unit while you had it apart inspecting / swapping the 4 bias rollers. I had one earlier in the week on a C7100 where the previous...
Like slim said need the jam code to really help you out, that tells us what the machine is seeing.
You can try turning off temporarily the double feed paper diversion as well to help you...
I would try to install a fresh bottle of toner as well, have seen lots of problems caused by toner that has sat for a long time. would try to evacuate as much of the old toner as you can.
Sorry about that those are on the C7100 series but i don't see them on the C751, my apologies been along week lol
Hello,
Do you mean Pro C751? If you more than likely its the chuck on the piece that pulls the toner cap off. the little wings that hold the parts together break off I have had to replace...
i only replace the gears when they become excessively worn or get damaged. They do require periodic lubrication though i think the manual states every 600K to put some grease on them.
I replace the AE030086 bearings as well as the above mentioned parts there are 4 ( 2 for pressure, 2 for heat roller) and the heat roller bushings as needed. Usually every other rebuild or as...
Have some experience with the 8300s, They love to be run if the customer runs them a lot the PM parts will make life and most of the time go over. I have machines that consistently get over 1 mil...
I just had to patch a linux fiery for the Pro C5100 for the July 2020 security updates and the damn thing took 25 minutes each time to reboot in between the 7 updates. Have patience. especially if...
Change all of the filters (+ ozones) there are 6 or 7 of them and clean all the toner / dust out from the vents and go from there. Machine is running hot and the fans are cooling it off probably...
Are your test prints off the engine or the fiery? i ask because i had a similar banding issue with a customer running a gray background you could see a magenta band it it ended up being a setting...
if using a full color solid fill logo The image density will look slightly off if you print close the corners where the back and the sides are glued together to form the envelope. because of the...
The toner formulation is different between the 2 series so its a possibility, I do not miss working on these though I went through so many PCDU units such a environmental waste.
yes, sorry remove mylars and re-install the punch unit, while you have it out good time to clean and LIGHTLY lubricate the punch dies
This also happens on the SR5050/ SR5060 finisher on the Pro 8100,8200, C7100, and C9100 the mylars get warped and chewed up and causing jamming, just take the punch unit out and remove them have...
You can use Chemours Krytox XHT-S as its fluorinated in place of the Fluotribo MG and Barietta image supply sells it or you find it on amazon the Silicone grease i just used the ricoh part i...
What exactly are you lubricating in the finisher ? I was just curious.
i use the SP 2-109 in a pinch as it allows me to check the dr blade and charge roller but i also have the files i can load on the fiery with the different percentages of toner mixing. i have just...