I purchased a stair climber many years ago they’re expensive but it saved many money back so I’m sure by this point bringing a seven or 800 pound machine up if I the stairs without it is scary. And...
Type: Posts; User: Riviera
I purchased a stair climber many years ago they’re expensive but it saved many money back so I’m sure by this point bringing a seven or 800 pound machine up if I the stairs without it is scary. And...
Hi. Can anyone help me with firmware for a 3551ci I have a customer who needs to be able to scan Smb 3 and their firmware is too old to support. It requires 6 or higher. Thank you
Hi. Can anyone help me with firmware for a 3551ci I have a customer who needs to be able to scan Smb 3 and their firmware is too old to support. It requires 6 or higher. Thank you
Hi. Never disturbing if your kind enough to help. I’m sorry for delay in responding. I’ve been dealing with personal things and put this aside. But it does need to get fixed so thanks. I was...
[QUOTE=Quatro;1647931]it was working before?[/QUOTE
The machine was working one day and when I got to it it was dead. All the symptoms I’ve explain are the symptoms a had since the first time I...
Nothing happening on control panel. It’s blank. When you power on machine the only sign of life is the soft switch blinking and you hear the relay above the power supply trigger then after 30...
Thanks for that info. But what do you mean put the monitor in controller?Also the HDD doesn’t come on I’m not sure of sequence and it’s not getting power What do I need to do to reload SS ? I...
I got an Oce plotwave 360 that’s has no life except for the soft power switch blinking, and leds on the spider board. I have no access to service manuals so I’m goin in blind. On the regulated ps I...
Can Somebody help me with the part numbers for the oce plotwave 300 thermistors and the part number for the entire fuser thank you so much I appreciate it
Customer is getting an Error related to problem with fuser They didn’t write down code but were told it was a fuser error. I got there and it was in a fuser jam error. Cleaned fuser entrance paper...
Machine comes ready to hit the copy button it says copying and doesn’t do anything else. Every so often a copy will come out but it keeps saying copying even after the document comes out if you try...
All color units installed less then 10k and 4 months ago. Customer says the tinting started soon after but only recently called. I suspect yellow is over toning.? Is there anyway to correct with...
I’m not sure if hat version firmware is in machine. This is my first time working on it. I’ll check that and update if necessary. But at this point. Machine says ready to copy. No repl imaging units...
I’m not sure if hat version firmware is in machine. This is my first time working on it. I’ll check that and update if necessary. But at this point. Machine says ready to copy. No repl imaging units...
i meant a wire with a connector
That’s the issue. There is a spot in the imaging units behind the cover where I can clearly see a spot that the chips would go. But there isn’t any there nor is there a word assume with a plug to...
How do I reset drum count? I have the chips but there is no wiring in imaging unit to plug them into?
Im getting l 1 l 2 and l3 code
e after setting soft switch 51 and 55 to extend drum life. The imaging units do not have chips in them or the wiring to connect them too .I assume they are original?...
Ihave a customer who has forgottin their admin password. It hasnt been a problem till now. I had to chang printer controller and hd. Now i need to input network settings.Can any one help with a...
so now I have everything turning ,ill make sure all toner removed from hoppers reset 3-1 to 0 power down/up put fresh bottle in and be good to go thanks for taking the time on a Saturday to answer...
Thanks so much Lee . I actually did reset that , but im not sure i did it right ? I found dip switch 3-1 entered 0 and turned machine off then back on? Did i miss a step? II guess the code isn't...
thanks to everyone who answerd. UPDATE. customer was outta country till this week. I went back vacuumed everthing including tubes. Changed and calibrated dv. Ran 50 copies or so all good. went...
Customer asked me to look at his 951 . I take care of his Canons. According to him , The wrong tyoner was out in machine. He had someone come out and clean out developer unit and replace developer...
customer stored printer 3 months and white clogged. I know he can put cleaning solution in machine to try n unclog but is there any other way manually to unclog
Im getting error 4531 when machine calibrates or prints in color. Cant find code anywhere. Customer just bought used so I need to have manual . thanks