I am needing a HDD. Is there a Software Package that has to be done to get it to work in the machine? Error F510 Code
Thanks Hoosierdaddy
Type: Posts; User: Hoosierdaddy
I am needing a HDD. Is there a Software Package that has to be done to get it to work in the machine? Error F510 Code
Thanks Hoosierdaddy
Anyone having SC142-12 Codes coming up? There is a Bulletin that came out that said they were working on a Resolution but havent seen anything yet.
Thanks Hoosierdaddy
The machine is acting weird. Put a full set of HP Inks (standard capacity) Says Incompatible ink cartridge (all 6 Cartridges) It is also saying to replace the middle Print Head (which i have...
Thanks for the Reply. There is a border on the prints. Also when i printed a Test print out of memory it didnt print it from border to border on 36 inch paper. should it?
Prints some documents in wrong direction on paper. Could this be caused by the Print Driver? It has also printed like 2 inches of a blue print and stopped printing. Customer will have to unplug...
Any Ideas how to fix this issue. Does it need a HDD or can it be reformatted?
Thx in Advance
Hoosierdaddy
Would someone be kind enough to let me have access to the Service manual for this machine? This machine has black lines on it and it still has 70% left on its life.
Thanks in advance
...
After a closer inspection of the Cutter, the latch was broken off of the cutter assembly... Thanks
The Customer has replaced Fusing Unit. Is there a procedure to resetting the Error? And if so is there a procedure to Reset this error Said there wasn't any specific Error Code on the machine.
...
Have 2 Separate Machines Running Light even after Replacing Developer and DV Unit. Did Tech Bulletin About Exhaust Fans Ect. Any Suggestions?
Thx
Hoosierdaddy
[QUOTE=Kiran Otter;2350243]There's no adjustment. Make sure you can push the carriage and engage the cutter by hand. It could be the 'hook' on the carriage is broken off
Thank You
I've taken out the cutter and it seems to be ok. Could the carriage not be going far enough over to engage? Is there a adjustment for the travel of the carriage ?
After completion of a print job the carriage goes to the left but the cutter doesn't attach to the carriage to cut the paper. Any suggestions or reason it wouldn't do it?
Thanks for Input
...
Thanks for the reply. I will check that out!
Thanks for the tips, the fusing unit is new. I will check the coupling Drive gears
The Top 4 Lights are Yellow and the bottom 4 are green if that helps solve the mystery.
Thanks
Hoosierdaddy
I am Trained on the machine. it is being fed LEF and is is letter sized paper and regular 20 lb paper Its as if the fusing unit wasnt rotating and after closing the transport section firmly it got...
It was jamming (J082) and wouldnt stop, released the transport levers and reseated transport section with some force and the machine made a pop pop noise and started working. It has done this twice....
There isn't anything behind the Tray, would this indicate the lift motor is defective or a sensor out of whack? Or is there a reset for this message?
Thanks
Hoosierdaddy
Kiran,
Thank you so much that is exactly what the issue was. Thanks again!!
Replaced Drive Belt. Machine will not load Paper. When trying to program the settings in the paper menu the paper roll portion has a lock symbol when trying to select Paper roll / Sheet. Is there...
Machine is not going thru Inital. Has green light on and gets so far and starts over. Is this the Hard Drive? If so is the hard drive hard to replace and is there steps to do after replacement?
...
Its the Control Board Needs Repaired or Replaced
All the Ink Cartridges have expired Expiration Dates. Is there a way to use them with this condition? Firmware Ect??
Thx
Hoosierdaddy:confused:
Looking for parts for this unit feed rollers and franking rollers. Model m-236a
thanks for any help or suggestions