hello people! i got a stubborn problem with c258 since Summer. client call for "shadows" on printed image, turned out that there was slight color shift on prints. tried to do...
Type: Posts; User: lazymangr
hello people! i got a stubborn problem with c258 since Summer. client call for "shadows" on printed image, turned out that there was slight color shift on prints. tried to do...
hi again! it was the polygon motor indeed! a good cleaning and it is good as new! thank you guys!
thanks guys! i will check it and come back to you with results!
here are better pics Imgur: The magic of the Internet
i got a c224e that all prints are fainted all across on the top side on all colors. i attach a pdf with scanned gradation.ignore the distortion of the banding on the scan, its due to a not so clean...
hello! i have a question. i must change devs on some 8 series machines. does the black dev fit on color dev slots as the previous 4 series?
coming back again with solution. unfortunately the sys board is fried. thanks all for the help!
thanks for the aswers. i have a same model donor machine in service. swapped power supply and HV board, tried with all consumables out of the machine ( iu + fuser) and all doors open. nothing...
hello! just got a call from client that on powerup the machine goes to 2/9 booting steps then reboots, again 2/9 and reboot. cannot acess any mode for update, 08 menu etc. swapped memory ram and hdd...
thank you for that info, i used that a lot and works. but how about 8 series machines? i have searched all forum, didnt find anything. i am 99% sure that will work, but is there anyone done it?
if you changed all that and still you get jams 1st check if the door not closing good. try to print while you press the door against the machine or clean the vertical rollers in the small jam doors...
Looks like it was way off and was interfering with the ruler attached to the platen glass. Copied numbers from another machine and problem gone. Then I did a fine-tuning from there. Thank you all
thank you all for the help and time.
ok after all the procedures above and contacting konica hit a wall, i stumbled upon service mode menu-> machine -> scan area and comparing to other machine was...
If I raise the adf on the right side enough that don't actuate the sensor it works but it's messy because it don't start the procedure to read the platen glass if there is paper. It only works as it...
nah I am far from it. All boards that reference to scanning are replaced but no avail
As I said I already replaced scanner board and lens board from other working machine as Konica suggested but it's the same thing. Tomorrow I will contact them again since there is no other option...
Nop. No scanner board no lens board from other machine. Same thing.
That's right it works if I remove the reed switch because it don't enable the paper size detection. But that's not right. I am now replacing ccd and scanner board to check
It's a leasing return machine with low meter. Tried table 1 and 2. But table 2 is for machines with 2 sensors on the right. The only way that it works as supposed is with the platen glass removed....
I used 2 different adfs platen glass and slit glass from other working c258 machines to check. I done all the sane procedures. Now I am in the insane spectrum
Hello everyone! i have a c368 with the original left on glass when i lower the adf. what i have done so far
the machine has only 1 original sensor for a3 in the right side of the platen glass...
I think it needs thickness more than 1 paper. Try fold it 2 or 3 times
yeah i am aware of that. i just ask if there are parts so i can do it in my office and just go to customer and plug and play instead of swapping the covers on field
hey. have anyone found spare parts for the color drums holder-spacer so i can add black drums on color unit but build them in the office and not in customers office?
hello all !
a customer got c3100p with 36k total counter. called for total black page on print. on visit i test printed counters etc and saw the page total black like 200 halftone and you could see...