Search:

Type: Posts; User: afterhours

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    532

    Re: Ricoh C901 stuck saying Printing

    No. I will try that.
  2. Replies
    4
    Views
    532

    Ricoh C901 stuck saying Printing

    Hello, I have a C901 that comes to idle, i send a print job, the machine seems to receive it because it goes to printing with the document information but machine never prints, just keeps saying...
  3. Re: Ricoh Pro 901s Graphic Arts Edition SC 674-01, SC 676-01

    So i got that problem resolved. It the transfer belt power pack some how shorting.

    Now I have s new problem, the machine comes to idle but when I send it a job it just sits saying printing...
  4. Re: Ricoh Pro 901s Graphic Arts Edition SC 674-01, SC 676-01

    I do. I will replace them tomorrow.

    Only question is fuse.on.controller? Not familiar with it. I guess I can start with replacing EA2 and EB. Already replaced G.

    I'll get back to you...
  5. Re: Ricoh Pro 901s Graphic Arts Edition SC 674-01, SC 676-01

    When you say the interlock switches. Is there a specific one? Both front door interlocks?

    I'm only getting 24v at the fans. Everything else is 5v.

    The relay board is putting out only 5v but...
  6. Ricoh Pro 901s Graphic Arts Edition SC 674-01, SC 676-01

    Hello, any help would be great.

    I'm getting an SC-674-01 AND SC-676-01, I've replaced the Relay Board and PSU-EA1, harness looks good. still getting same errors. It started on Monday over the...
  7. Replies
    9
    Views
    2,027

    Re: Canon ImagePress C700

    Thank you. I did that and then replaced the whole patch assembly. I think running halftones because if there is something wrong with a drum unit I will be able to see. But for the life of me I cant...
  8. Replies
    9
    Views
    2,027

    Re: Canon ImagePress C700

    Do you know how I can run the halftone test prints? That might help me figure out which drum is the problem.
  9. Replies
    9
    Views
    2,027

    Canon ImagePress C700

    Hello everyone. Thank you in advanced for any help you can provide.

    I am a Konica Minolta Tech. A customer of mine recently inherited the Canon Imagepress C700. It has turned out to be an...
  10. Replies
    6
    Views
    599

    C7000 with magenta covered prints

    I'm working on a c7000. It keeps giving c2452 when starting up. I've replaced magenta developer, swapped magenta drum and charge unit, customer also had another used magenta developer unit in a box...
  11. Replies
    5
    Views
    1,345

    Re: C7000 with C4603

    I'm sorry it took so long to respond. I printed test pattern 80 and photo 1 and 2 is what I got. Picture 3 and 4 is what I got after and auto calibration.

    My question is why wouldn't it auto...
  12. Replies
    5
    Views
    1,345

    Re: C7000 with C4603

    I'll get it posted tomorrow. Thank you
  13. Replies
    5
    Views
    1,345

    C7000 with C4603

    Hello, I'm having an issue with a C7000 giving me a C4603.

    I've changed the Cyan developer, replaced the color registration assembly, replaced printer controller board. I don't believe it's a...
  14. Replies
    0
    Views
    353

    C7000 with Creo issue

    Has anyone had the issue I've attached as a photo. If so, have you found a solution?

    Thank you for any suggestions.49242
  15. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Re: Bizhub 458

    I had not seen that post but I did check both belts for tray 1 and 2, and the lct was swapped.

    Thank you

    Sent from my SM-G981U using Tapatalk
  16. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Re: Bizhub 458

    Thank you. I'll check that.

    Sent from my SM-G981U using Tapatalk
  17. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Re: Bizhub 458

    The paper stops when it reaches tray 2. You hear the paper buckle just before this happens.

    If I cheat the door it comes.out of the lct just fine but then obviously jam due to the door being...
  18. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Re: Bizhub 458

    Firmware is up to date. The machine has 53k total on it. I'll check soft switch 10.

    Sent from my SM-G981U using Tapatalk
  19. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Re: Bizhub 458

    Can you describe what you mean by the yellow paper seperator.

    Sent from my SM-G981U using Tapatalk
  20. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Re: Bizhub 458

    I checked the paper size option for the lct and it is correct.

    Sent from my SM-G981U using Tapatalk
  21. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Re: Bizhub 458

    This is a used machine at the customers office. Paper path is clean. Sensors have been checked.

    Sent from my SM-G981U using Tapatalk
  22. Thread: Bizhub 458

    by afterhours
    Replies
    21
    Views
    3,229

    Bizhub 458

    Hi everyone. I have a customer with a Bizhub 458 with a LCT large capacity tray 3. Every time the machine feeds out of tray 3 we either get a wrong paper size error or jam 99-01. We ended up swapping...
  23. [Misc] Re: DF790 pages misaligned when stapling & 3 hole punching

    I realize this is an ancient post but I have a customer that asked me to look at his Kyocera. I only work on his Konica Minoltas and this post is describing exactly what his finisher is doing. I have...
  24. Replies
    3
    Views
    2,364

    Re: konica minolta c284e c2554 code

    This is going to sound crazy but replace the drum, replace toner filters, if you have a used developer unit, add developer.of the same color. You will have to eye ball it as I am not aware of any...
  25. Re: Konica Minolta C5501 Gears under ADU worn out

    Its the same as c6500. I can get you that parts manual.

    Sent from my SM-G981U using Tapatalk
Results 1 to 25 of 151
Page 1 of 7 1 2 3 4