Search:

Type: Posts; User: donking289

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    4,978

    Re: Sharp \ Lexmark cross reference

    Thanks! This is very helpful.
  2. Replies
    0
    Views
    554

    Sharp \ Lexmark cross reference

    Does anybody have a cross reference for the Sharp 7-series(LUNA) and the Lexmark models?
  3. Replies
    12
    Views
    4,978

    Sharp \ Lexmark cross reference

    Does anybody have a cross reference for the Sharp 7-series(LUNA) and the Lexmark models?
  4. Replies
    9
    Views
    1,147

    Re: DX-B printers

    They don't like envelops. We had to take back 2 of them.
  5. Replies
    10
    Views
    4,430

    Re: Sharp new printer

    These are calculated with Sharp cost with a 40%GP. I have found that not all of them are crazy expensive. Some are just a little expensive.
  6. Replies
    10
    Views
    4,430

    Re: Sharp new printer

    Toner for these "Lexarps" are expensive. The MX-C607P for example, all inclusive comes out to .02 for mono and .10 color. And this is at the standard yield of 6% black, 20% for the colors - 5% for...
  7. Replies
    3
    Views
    1,270

    Re: IMC300 DF skew

    Yes this feeder looks very similar to the C307. We thought of the hinge screws, but these were not loose. We even took a dremel to the holes in the hinges to try adjusting the way the feeder sets on...
  8. Replies
    3
    Views
    1,270

    IMC300 DF skew

    We unboxed our first 2 IMC300. During check out we noticed that the front side being fed thru the DF has a noticeable skew, around 2mm on all sides. The back side is fine, so the paper traveling...
  9. Replies
    10
    Views
    3,571

    Re: MP2501 problems with w10

    Disable the WSD protocol via WIM. We are doing this to all units as we see them. You can configure the driver for an IP port only to have Win10 change it back to WSD. Too much automation in Win10!!
  10. [CQ] Re: 2501 with dark bands on back of paper 50mm apart

    enabled PTR cleaning cycle, which appears to off by default. bands are gone
  11. [CQ] 2501 with dark bands on back of paper 50mm apart

    during previous efforts to address light copies the following were changed: rebuilt fuser, rebuilt PCDU with new DV tank and roller, HVPS, LSU,& BICU. Firmware was updated. Now the front side...
  12. Re: tray rollers mpc3002 (orange) versus mp4000 (green)

    There was a bulletin that the 85s replaced the 90s for standardization. The 85s are cheaper by a little. Can't say if one last longer, they seem to be about the same.
  13. Replies
    6
    Views
    2,404

    Re: MP301 scan to email

    All of our refurbs get latest firmware before they leave the shop. So many changes these days, SMB, TLS, etc.
  14. Replies
    7
    Views
    3,892

    Re: Ricoh MP501 Opinion

    Not one fuser has lasted to yield.
  15. Replies
    14
    Views
    3,684

    Re: @remote SP C262SFNw

    If you are logged in as admin to the WIM, there should be a section for @remote setup under the Machine Configuration.
  16. Replies
    3
    Views
    3,864

    Re: Ricoh MP C5000 Address Book Error

    Address books are stored on the HDD, maybe it is starting to fail.
  17. Replies
    1
    Views
    53,821

    Multi level color click charges

    Is anyone out there using or discussing color click charges based upon toner coverage? We are considering the idea and would appreciate any feedback.

    Thanks
  18. Replies
    1
    Views
    2,330

    SP C252 with Internal Misfeed

    SP C252 shows Internal Misfeed during warm up. The registration sensor, exit sensor, and paper end sensor have been checked with a meter at the Engine Control Board. There are no IO checks on this...
  19. Replies
    4
    Views
    769

    Re: Mp C4502 address book issue

    Does each address have a Title or added to the Frequent tab?
  20. Replies
    3
    Views
    1,076

    Re: M3550idn disquised as a Ricoh

    Yes, the new sep pad assy came with springs. I did find some other springs with more pressure. This seems to have helped. Time will tell if this resolves the issue without any negative side effects....
  21. Replies
    3
    Views
    1,076

    M3550idn disquised as a Ricoh

    I'm not 100% on the model, but anyway, this relabel has had doc feeder multi feed issues since install. Only 25k on this, but changed out sep pad anyway. Does OK on first part of packet, then multi...
  22. Replies
    0
    Views
    411

    MP 501/601 SPF doc feeder multi feeds

    Only 25k on this, but changed out sep pad anyway. Does OK on first part of packet, then multi feeds when down to about 10 originals remaining. Not just double feeding but taking in 3 or 4 at a time.
  23. Thread: ARM257

    by donking289
    Replies
    6
    Views
    1,377

    Re: ARM257

    Fixed a couple of these with new ribbon cables.
  24. Replies
    9
    Views
    6,096

    [Error Code] Re: AR-207 Code U2 40

    R.I.P.
  25. [CQ] Re: MPC 3003 Thin colour lines when using the DF

    I have seen very thin scratches in the slit glass do this. Clean the glass and all is good for a time. On one particular, ending up replacing the glass.
Results 1 to 25 of 28
Page 1 of 2 1 2