8353ci already has "attachment kit" by default.
Make sure the plastic flap is installed at the upper paper exit so that sheets destined for "output tray C" cannot fall into the gap between the...
Type: Posts; User: sparkycivic
8353ci already has "attachment kit" by default.
Make sure the plastic flap is installed at the upper paper exit so that sheets destined for "output tray C" cannot fall into the gap between the...
Name and shame the paper for us, please.
I've got a school who just changed to a paper by Grand & Toy which "seems" to be made for printing on one side, while claiming to be "laser compliant". They...
was any toner leaking out of the developer or drum ?
what condition did you find the developer and charge roller?
You might also want to inspect along the HV lines toward the PWB's and the HV PWB surfaces and machine frame for dust/toner attracting...
C6770 IH Low Power error
When I have this, I check if the IH coil is seated in it's attachment and springs are resting properly.
One specific traumatizing experience with C6770 , turned out to...
if: using OEM toner, AND "silent mode" engaged to save fuser
then: success will be enjoyed.
paper feed rollers: change at 100-150K .
every single one of our units has a printed label on the top of the toner area door instructing them to "use empty black toner as new waste container", and also a label "Waste" on the waste door. We...
Mark the gear of the toner container with paint, and try again, see if the gear actually turns or if it's not turning. The problem might be damage of the contrainer drive mechanism.
This has been asked, and solved many times.
such as... can't connect to the web page of the kyocera tasfalka 4501
check that all other containers are fully seated... they give confusing errors when they shift inside the housing.
If the device is "adding toner" a lot, and then complaining about the black...
I had good print on the belt, and no C76xx in the log, so that's why i started at secondary transfer, yet my cure ended up being found at the drums/dv section wtf. working backwards from the...
all of my colors were faint, which is why i was chasing secondary transfer first.
I vacuumed the sleeve surface area of the developers, as well as all of the exterior surfaces per usual.
I tried...
I had another call yesterday with this issue. I worked backward from most likely to least likely cause of issue (2nd trans, trans HV pwb, HV conductors, contacts and springs, primary trans all of...
I had this once in my fleet. It was one of the pandemic-built devices where the screws on all of the boards weren't tight enough causing electrical gremlins or killing random boards.
Tighten all...
"compatible" toner... gonna have to try your luck with another version. I've never seen waste pluggage in our fleet of similar models using OEM toner. Nobody's saving money with that knockoff stuff...
can you prove if the yellow developer is actually turning?
Have the firewall admin ENSURE that TLS/SSL inspection be DISABLED for traffic to/from these devices. If they can't prove that the traffic is unmolested, have them create a firewall rule/policy that...
*sigh...
it's solved long ago
taskalfa 5501i scaner
important part:
It's actually not so much the bearings or their quality, but is the way that the bearings are implemented. the shaft sits in the bearing by a "press-fit" , possibly using temperature shock to put the...
This has been solved in a previous post regarding TLS in web browsers.
You need to find the setting inside your web browser to allow connections to websites offering the older version.
Here it...
I either forgot to take pics, or lost them. Here's the place where it goes... Just make sure it goes into the curved area which is where the resting position of the roller goes when the door is...
I never needed to go back to mine after applying the shim to the ak door, so there's that.
I see you tried to get inside your bridge... I had mentioned in a previous post that going in from below...
this copier has another "standby" 5v PWB hidden. I think it's somewhere in the back, upper area... Been a while. BW model has same STB5V pwb, but is installed in laser compartment.
you can improve the life expenctancy of the parts for these tabletop machines with more aggressive power saving settings... we used to target 60 minute "low-power" and 90 minute "sleep" but have...
Don't forget that this model uses an optical sensor on the underside of the drum unit, which can get dusty, as well it as a lever sensor just at the registration roller which might get dust falling...