Check the scan settings, sounds like the from email was changed and then set as default.
Scan/Fax button, then go to Name/Subject/File Name at the bottom and check the email there.
Change it if...
Type: Posts; User: KMFLT3CH
Check the scan settings, sounds like the from email was changed and then set as default.
Scan/Fax button, then go to Name/Subject/File Name at the bottom and check the email there.
Change it if...
Just released today...
C5372 (CPU temperature failure) may occur during PC printing or low power/sleep mode.
CAUSE: G00-K8 firmware contained a change designed to reduce the noise output of...
Bit assignment from left to right:
76543210
00100000 (for your question about enabling the VOIP setting)
It actually begins at zero and from the right, if you are counting up.
I've had to do this on a handful of machines, haven't come across the option not being there. Switch 237 should look like this:
Switch No: 237
Bit Assignment: 00100000
Or just do Switch 237...
For this particular model line, the shaft where the lower idler rollers ride. The ones along the bottom in my video. If you run the exit rollers like mentioned you can lubricate them and work it in.
It's the exit rollers.
i-Series noisy exit rollers
You need to get the inner finisher off and out of the way, then the horizontal metal cover plate under the finisher (not shown in your picture). The PH is under all that, held in by 3 spring loaded...
Yes, it is. The fusers on the i-series don't last nearly the stated yield.
I series premature fuser failure
Make sure the plastic finger on the rotating assembly isn't snapped off, this is what engages the dump from the belt into the chute. If it's broken the toner builds up inside the belt's auger and...
Disable smart fusing control
Increased fusing temp +10 across the board
Set fusing transport speed to 0
Ah yes, completely forgot about this issue and I've had to lube dozens of those plastic shafts that the gears ride on. That and noisy exit rollers on the main body. Oh and squealing drum unit shafts....
I'm not. I would rather work on an 8 series.
Just saying the i-series aren't that bad except for the desktop models.
I have been installing and servicing i-series for 5 years next month and they are no different than the rough start the 8 series had with all the HDD and MFP board failures, the infamous lock ups on...
Oh it definitely will get it out of a toner end condition, can confirm as I just did it last week on a C750i that was completely down and "out" of K toner.
Bottle was full but there was a broken...
61721
This resets the toner gauge to 100%, regardless of how much toner is left in the bottle.
Works on color 8 series and color i series (A3)
I don't think I've ever tried it on a monochrome...
You'll need more than just that sticker/label to properly fix it. If you look at your picture closely at the inside edge of the hole there is a small amount of plastic at the top right and bottom...
Yes, those are the exact ones I use on Firefox.
On privacy badger there are a few settings to change if you want to block the youtube video blocking overlay they rolled out when using an ad...
So are you saying this function is not working correctly on the MFPs even though it's enabled? Here's what I found on it:
MFP repeatedly reacquires an IP address until the MFP obtains an IP...
Now that is funny!
Replacing the drums cleaned up the prints a little, however some faint speckling was still evident. By the time I had returned with the HV board, the problem was just as bad as before. All 4 drums...
Yeah that is odd, I am seeing the opposite in the service manual. I've personally tried -20 and it was worse than +10
61316
Depends on if you're using genuine toner or aftermarket. I've had dozens of i-series fusers fail prematurely even with genuine toner. If toner smears off the page I do the following first:
Disable...
HV Board.
https://www.copytechnet.com/forums/konica-minolta/173224-background-i-series.html#post2343917
I've come across this a few times now, the primary cause is non-genuine toner. Haven't...
uBlock Origin and Privacy Badger is all you need. Still blocks youtube ads and that dumb overlay/warning they've been rolling out. These days no one should be browsing without an ad blocker IMO.
Came here to say this, I've come across this problem a handful of times on various models.
Re-enable all the life stop settings in service mode, tap End then back out to the ready to copy screen....