Good morning,
sorry to bring up this message in 2023, but it's to thank dwarf for coming back to give his solution.
This MFP is old and I have one left that is resistant to replacement.
I got the...
Type: Posts; User: dmary
Good morning,
sorry to bring up this message in 2023, but it's to thank dwarf for coming back to give his solution.
This MFP is old and I have one left that is resistant to replacement.
I got the...
Good morning,
first, there is a simple check to do.
1 - turn off the MFP,
2 - open the DSPF rear cover,
3 - check that no paper clip has fallen on the DSPF control board.
Next, what are the...
Good morning,
Here is a problem we are dealing with at the workshop with an MX-2651 (firmware: V6.10.Z2) and we have not yet found the solution. I hope for some help from you.
On Sharp's...
Hi !
Someone to kick this s*** spam !!!
Good morning,
there is a problem with dry toner stuck to the pressure roller.
The best is to change this roller (MX-601LH).
Sometimes I still install the old ones (MX-607LH).
Sometimes I just...
In some cases, ''H'' trouble codes may occur due to contamination or damage to the fuser assembly connector terminals.
Fault code H2, H3 random paper jam
The male connector on the oven...
+1 too for 44-02 44-27 44-06 et 44-26
Hello,
This is a known issue and simple to clean up.
It is also possible that F2-78 codes (non-blocking) appear from time to time?
Faded copies may also disappear for a moment when opening and...
Hello, you write to us that you have replaced the HDD.
Is this an ordered HDD from Sharp? Was it a new HDD?
If it's an old HDD, did you format it from the MFP?
When I have an E7-93 code on...
Hello,
I'm not sure, but it may look like a HDD problem.
Hi!
Shading adjustment (calibration)
(DSPF Mode)
This adjustment must be performed in the following cases:
• When the DSPF CCD unit is replaced.
• When a U2 trouble is occurred.
• When DSPF...
Finally, we are replacing the MX-7580 with an MX-6580. It's slower... Anyway, the MX-FN22 Finisher slows down the machine. And this MX-6580 has less than 500k.
This is not a good technical...
Good evening,
It's a good idea. No, I didn't, I don't think about the quality of the paper because I don't have any problems with other colors.
Just yellow.
I think I'll close this topic next...
Good evening,
thanks for the tip. I edited my user registry backup file leaving only the admin account. It allows me not to touch other accounts.
If the administrator password and the service...
Hello,
the corona can be polluted by the old toner if the mylar above the drum cleaning blade is deformed.
Personally, I always have one in my car.
(PSHEP6761FCZ1 - Toner receive sheet)
Hello,
I still have the same blade area problem. We manage to have a good quality overall.
But the problem sometimes comes back unexplained.
I am awaiting a response from Sharp France. It's...
Hello,
Thank you for the answer, I feel less alone and sorry for this translation. I read Shapkespeare's language well, but I write it less.
I reversed the connectors coming out of the MC PWB...
Hello,
Thank you for the answer.
the MFP is therefore moved against a wall in the same room.
The pale area is still there, but less strong.
I think I must have a stray light in the machine, or a...
I have already replaced the LSU. I wrote it above (Laser Block).
On the other hand, I did not indicate that the MFP was against a large one in front of a large window.This afternoon, I moved the...
SHARP MX-7580.
I'm French and this post is translate by Google Traduction.
The simple tip: a pale area in the middle of the sheet in 1/2 yellow shade:
SHARP MX-7580.