now that I am reading your request, I am at home, and I do not have access to the documentation, however, if you are in a hurry and have some machine or printer retired for end life, only must be of...
Type: Posts; User: luca72
now that I am reading your request, I am at home, and I do not have access to the documentation, however, if you are in a hurry and have some machine or printer retired for end life, only must be of...
follow this attachment (62375).....seems like the same thread as a few days ago(?)...LOL
This is how I solved it on the phone a month ago... except unplugging the network cable
well... if your problem its the privacy...you could also attach a counter page! so i have to guess.
I'm betting on the film on the sleeve, which has lost its non-stick coating at one point (as long...
I tried to remove the SD card, and the scanner and printer do not appear, with the card inserted the scanner works, and the settings in user tools are there, they are only missing from the web
thanks friend👍...we no longer have that model to be able to verify, I hope it's the corrupt firmware, I'll let you know as soon as I go to that customer with the SD and romdata modules.
Hi everyone, I'm asking you for confirmation, now I'll explain what happened to me:
I went to replace the hhd of this mp9002 for the second time, which the first time gave sc672-00, ok fine
then...
usually when the machine eats up the toner, you have to replace the pcdu of that colour, it happened to me a few years ago on mpc2003 with yellow, (I had also opened a discussion here) I recommend...
you can notate bad hhd when you load the address book in wim, that load very slow, anyway a bit time ago , sc672 by bad hdd its happen also to TULIO here.
it happens every now and then, last Friday mp9002 sc672 replaced hdd.
a month ago mpc2503 sc672 replaced hdd, and others that I don't remember, a good way to understand it is the speed of access to...
replace the hdd for first thing
it's the first thing I did, and I found solutions like "turn it off and on" or "unplug and plug in the formatter", but since the customer is very far away (it takes almost a morning) I would be...
Hi everyone, I usually stay in the ricoh/lanier/gestetner section.
we have this customer reporting this problem on that unit
(61.00.03) print head error (on display)
I'll start by saying that...
I advise you to remove auto-select by selecting tray 1, and to store the condition in delfault mode in the "program/store" button, the one with the memory symbol (the diamond), and set drawer 1 in...
finding the right diameter, you could try cutting a piece of those insulating foam rubber tubes, which are used to prevent outdoor water pipes from freezing....but that's fine.
62268
[SOLVED] it was just that stupid gathering roller that got soggy, replaced with AF03-2094, thanks for your cooperation
622346223562236
I think too, it's a problem that also affects internal finishers, which use that replacement, which is also quite expensive (32 euros!)
....I don't understand why they insist on using that...
Hi everyone, tomorrow I have to go and look at this problem, the machine was recently installed, and I checked both the machine and the finisher carefully before delivering them.
the customer...
I told you above what you have to do, the connector, and the termoswitch's, check the both plastic lever if lock well, and are no broken
bad fuser contact, if you want to try a cheap thing to do...
clean well the contacts of the fuser connector and those on the machine with a cotton swab and alcohol, you can also use a scrap of light...
if both cause problems, it could be a strong accumulation of dust, the ideal would be to dismantle both pick up stations from the machine, and give it a good blow of air....just to start off
try to check that in the paper cassette setting, where the weight is indicated, the "apply to duplex" item is selected
I don't remember how now
the cards of that model are engineered, but if it prints well from LAN, and not from USB, it could be the image processing channel of the USB part, I would try changing the...