If you swap fm1 for fm2 and the sub code does not change then I would suspect the DC controller as the fans are directly driven by it.
Just to verify: FM1 is part FK2-0806-000 and is in the...
Type: Posts; User: Etech50
If you swap fm1 for fm2 and the sub code does not change then I would suspect the DC controller as the fans are directly driven by it.
Just to verify: FM1 is part FK2-0806-000 and is in the...
My thoughts:
The 5200 was a good unit, the 5500 series is outstanding as already mentioned. Cost of drums and fuser are high but life is way better. If you can get a mark 2 or 3 5500 then that is...
Let's play identify the copier.
Central Intelligence (The Office Escape) 4K - YouTube
At approx. 1 minute in there are 2 copiers. I remember the first time I saw this and was surprised that...
Could you check the usb cable from the AIO to the scanner. It has to be a usb 3.0 (blue end color) and need to be plugged into one of the 3.0 ports on the AIO. The last unit I installed had 4 ports...
I agree with the timeline if you follow the book step by step and remove everything it tells you. Make sure you have plenty of room to spread out all the removed items. The annoying part is the black...
Where do I even start with this topic. With the amount of driving that we all do, you would think we have seen it all. The reduced traffic during this crisis makes rush hour commuting appear as if I...
There is a flow chart in the service manual that will help. It relies on what control panel lights come on and the pattern of the flashes. I have had success using it to find out what failed. (main...
Check the following:
COPIER> OPTION> FNC-SW> MODEL-SZ>1
COPIER> OPTION>CUSTOM>SCANTYPE>1
LEVEL 2>COPIER> OPTION> FNC-SW> SENS-CNF>1
Usually happens after some type of clear or reset.
I am basing this solely on experience with the 6800 series which has similar design. There was one machine that I remember having to change the turret drive assembly in the back. It wasn't very...
The 0108 jams seems to be only from the left deck. I would first look at the deflector that in under the fixing/feeder assembly. If you slide this out and look underneath, you will see it in the...
As far as the scan lamps being a thing of the past, we used to have a crush proof tube to hold all the different lamps, got rid of that long ago.
Also, as to physical books, we had parts manuals on...
The first thing I would check is the stapler. I remember troubleshooting this years ago and being stumped. Seems that the stapler can be empty and cause this very issue. The fact that the fuser is at...
This bulletin was for the 7000 series. The 7200 uses the same bottle but uses the reflector in the bottle to detect full not the window. There is a counter for waste but the message to empty comes...
Since the line seems to be in more than one color, the fuser film would be the first thing that I would check. You may be able to do a simple visual inspection by just opening the right doors and...
Most likely it is the dev middle stir rod, take the upper cover off of the dev and see if it is not attached. (FL3-2163-010) It has been an issue on all adv6000 series, the part has recently been...
I will assume you enables the long sheet mode in service mode: L2>option>user>MF-LG-ST=1
To get the meters to display on the counter check, you must change:
L1>option>user>counter5=471...
On the first service visit after install of a Canon adv6555, the customer was acting a little odd when I arrived. He asked in a quiet voice about what the office staff though was a "camera" the front...
The external delivery unit has a long life. I would change it around 3 million.
The info I have for 0213 also shows that all paper paths can be affected.
M13 drives the outer delivery roller...
I would go as a first call and budget 2 hours, don't try to rush. The drive gets gummed up bushings and only shows an issue when doing face down, it runs just a bit slow and the timing goes off. I've...
The spring for the sensor flag at ps35 has been a mod to FC8-9450-010 due to 0112 and 0212 codes. The shaft just before ps35 has a one way gear that should be checked.
The 0213 and 0113 was covered in a Canon bulletin and 2 items were indicated as an issue:
1. The easy part is to replace the brass bushings in the delivery door ( the one with the sep claws) with...
WOW!!! Gotta love youtube. It amazes me what is posted there about disassembly and service mode items. Nice find.
The 0320 sub code indicates that the toner door for the cyan is open while the main toner door is closed. This could be caused by having the toner door switch bypassed without closing the cyan door....
That board is a resolution switching board needed by the fax kit or the universal send kit. The machine does have a network jack, however, this generation machine did not come with the ability to...
Greetings to all!
I am a Canon only tech. I work on most products small to large, wide format, RIP's and connectivity.