Search:

Type: Posts; User: PrintWhisperer

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds; generated 49 minute(s) ago.

  1. Replies
    4
    Views
    358

    Re: InFo About Kyocera MA3500

    AS400 is special case. IBM/AS400 has many configurations for print data stream.

    "Native" must be defined as one of the common AS400 output formats. The 'supported' (and documented) AS400 printing...
  2. Replies
    1
    Views
    272

    Re: Kyocera Tech support web portal.

    Please provide this feedback (via your manager) to your regional System Support Engineer. The matter of 'too many' emails generated from Service Now operations has been raised and is a concern. The...
  3. Replies
    4
    Views
    358

    Re: InFo About Kyocera MA3500

    Yes. PDF data maybe be transmitted directly to Port 9100, FTP, or POP3 without driver involvement or in driver pass through mode.
    Any ‘Ready to print’ data (PDF, JPG, BMP, or TIFF) will be rendered...
  4. Re: medical software (Dentrix,etc) not being able to use Kyocera products

    As usual BC is on track so please do not get confused by this 'incompatibility' nonsense.

    DO YOU GET AN ACTIVITY LIGHT BLINKING when the job is sent or not? If it blinks a couple times and nothing...
  5. Replies
    23
    Views
    25,018

    Re: C7901 3252ci

    You are on the right track there, especially with the 24V supply and distribution. Usually you will have lost 24V coming off of the Image Drive PWB or Feed Drive PWB. You will find the 24V2 or 24v3...
  6. Re: Help - Unable to format new HD or SSD in TASKAlfa 3011i

    In the past, you could use a larger drive and it would only format and make available the 320gb spec. However, your C0660 code comes from the Data Security kit being enabled.

    If it wasn't, you...
  7. Replies
    20
    Views
    2,061

    Re: Low counts high toner usage

    Your OP mentioned BLK and nothing about color yields so settle down and take heed. We are professionals who help those who help themselves. No one here is paid to figure out your job for you. Every...
  8. Replies
    20
    Views
    2,061

    Re: Low counts high toner usage

    As KYO is trying to say, nothing to talk about until you look at the data. MM464 calibration setting to LONG. Ensure MM325 is OFF. KFS will get you the MM000 reports from anywhere, maybe you have a...
  9. Replies
    2
    Views
    436

    Re: 6230mfp ssd

    Use an SD Card instead. 16Gb or 32Gb and good quality (not all SD cards supported)
  10. Replies
    7
    Views
    769

    [Misc] Re: Kyocera taskalfa pro 15000c

    Yea I was thinking the spacing and size looks like something in the finisher. Most people do not get the DF-9100 and stick to the Stacker so it would be a seldom seen problem. Impact marks from a...
  11. Replies
    1
    Views
    465

    Re: Bypass configuration

    Please note correct position of side guides is required for accurate size detection when using 'Auto'
    59933
  12. Replies
    7
    Views
    828

    Re: toner collection bottle.

    Craigster is correct that you have to re-calibrate with empty bottle in U155..but the weight-sensor may be damaged.

    Machines are NOT TO BE SHIPPED WITH WASTE TONER BOTTLE INSERTED! It can damage...
  13. Re: KYOCERA TASKalfa352ci printing issue

    All trays produce same extra margin? Even MP tray? does U034 LSU Out TOP have effect? Mechanical isolation to probable failing/sticking clutch or roller is needed.

    Your tech is lazy, get a new one.
  14. Re: Prescribe command to move the print image left to right and up and down

    Do you mean A1/A2 and A3/A4? (Maybe I remember they were once labeled 'L' IDK)

    ...but this ignored in some emulation modes and will differ slightly in various emulations?

    You are way off in...
  15. Re: Prescribe command to move the print image left to right and up and down

    Only if the job is text only or has no margin/VMI commands of its own, which is NOT typical.
  16. Re: Prescribe command to move the print image left to right and up and down

    You should begin in U034 LSU OUT LEFT->MPT and adjust as necessary.

    You can not simply set margin setting commands to effect a job which is already encoded (e.g. PCL code from driver or app)...
  17. Re: Question About Most Recent Firmware and SMB

    Because we see options to turn off versions of TLS we sometimes think it should exist for SMB as well, but SMB works differently.* At least until the next upgrade where it gets wrapped in TLS but...
  18. Replies
    9
    Views
    1,600

    Re: White screen on TASKalfa 2554ci

    By crashing the OS. May need experimental firmware to fix it so contact your support rep.

    59049
    Black screen+Sleep light blinking->Remove network cable and white screen may appear. Also Panel...
  19. Replies
    9
    Views
    1,600

    Re: White screen on TASKalfa 2554ci

    White screen problem has been seen, but not for lightning/power surge. So perhaps you have a different problem like Op Panel Main or Main PWB...BUT

    Try to remove the network cable and reboot. If...
  20. Replies
    14
    Views
    1,304

    Re: M3540idn copying/faxing

    Send: Batch fax allows the system to NOT redial when scanning multiple fax transactions to the same number.
    Receive: Batch stores all pages in memory and prints when finished.

    Neither seem to be...
  21. Re: Taskalfa 8001i JAM 0000 02,03,10,15,19.

    None of these rule out losing voltage downstream.

    You have a sensor problem, THAT IS WHERE YOU START checking signals. Until you determine the sensors have supply voltage and are changing state...
  22. Re: Taskalfa 8001i JAM 0000 02,03,10,15,19.

    The 5V power distribution at the Feed PWB's is very delicate. In these models, wiring for individual feed units runs behind the left side covers. When replacing feed units, if you do not route the...
  23. Replies
    53
    Views
    5,344

    Re: Networking Online training courses?

    A+ is definitely more applicable to becoming a better technician by focusing on the PC hardware aspect in addition to basic networking. After all, MFP's these days are simply computers with a lot of...
  24. Replies
    23
    Views
    2,479

    Re: How money is made in copier biz?

    Start looking up authorized Kyocera dealers and putting in your resume. They are dying to get you...trust me. You will have the opportunity to advance your career and make more money. Stay where you...
  25. Re: When do you use U140 (Developer Bias Adjustment)?

    If you are an authorized dealer, just have your SSE out for a problem call, and happen to walk him past the toner cage holding that aftermarket crap. Maybe have him take a couple pics.

    The problem...
Results 1 to 25 of 440
Page 1 of 18 1 2 3 4