Search:

Type: Posts; User: Markks

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    664

    Re: Help! How to move C258…?

    I would not move it in a jeep. it would be worth the money to rent a truck and straps to strap it to the inside the truck.
  2. Replies
    7
    Views
    524

    [Misc] Re: "copers whith 5 slots"

    The AccurioPress C14000 has an empty spot that looks like it might be for a 5th color but currently it isn't used. KM said that in the future they my produce a machine with this frame with a 5th...
  3. Replies
    4
    Views
    332

    Re: Is a Bizhub 320gb HDD upgradable to SSD?

    I have successfully used 500gb SSD is eight series several times . I get them from Amazon for about $40.00
    PNY CS900 500GB 3D NAND 2.5" SATA III Internal Solid State Drive (SSD) - (SSD7CS900-500-RB)
  4. Replies
    7
    Views
    448

    Re: Weird density issue c258

    how old is the 2nd transfer roller?
  5. Replies
    4
    Views
    385

    Re: bizhub 227 prints lines

    Which orientation is paper running? What is life of drum, developer, transfer belt .
  6. Replies
    6
    Views
    654

    Re: More i-series problems

    Yeah but if the vent holes were in the correct spot it would alleviate this problem.
  7. Replies
    6
    Views
    654

    More i-series problems

    Noticed that on A4 printers and MFP's that the vent hole in the cover for the CPU does not line up with the actual vent holes for CPU. Which could cause CPU overheating and eventually CPU failure....
  8. Replies
    3
    Views
    452

    Re: Requesting a IC-418 service manual

    If you have access to mykonicaminolta go to one stop and search IC-418. Manuals can be found there
  9. Replies
    7
    Views
    839

    [Error Code] Re: Bizhub C300i D073 error

    If its running anything function level 2.0 you want to update to function level 2.1 before going to the newest which is function level 2.2. I would update to J-9 which is function level 2.1 after...
  10. Replies
    8
    Views
    3,649

    Re: check paper size for tray 3 on PC-410

    Its actually a damper . Its misnamed in the parts manual. It stops the cable pulleys from turning after you open the tray especially if its loaded with paper. If the dumper (damper) is bad the cable...
  11. Re: Replace Hardrive C458. and color patern on scan

    Your right, I should have clarified my answer better. If you know hdd or ssd is good and machine wont boot then try the reset tool. I have put SSD in several 8 series with no problem. The way I do it...
  12. Re: Replace Hardrive C458. and color patern on scan

    try running the reset tool. but even though the hdd was able to be formatted there is a chance you could have a bad hdd. If memory is correct I believe that machine has a 328gb hdd. I have used...
  13. Replies
    3
    Views
    471

    Re: Bizhub C452 wierd problem while copying

    I would reseat the cables on the ccd and where they plug into board. If that doesnt resolve your problem you may have a bad ccd
  14. Replies
    7
    Views
    403

    [Error Code] Re: Bizhub 423 C-C152

    Found the attached article, I was unable to find the kba listed
  15. Replies
    1
    Views
    187

    Re: IC-418 "FF" after running updates

    I would replaced the HDD with a SSD. Fiery will boot and run much faster. Plus with that error you could have a bad HDD . I believe this fiery takes a 500gb hdd, you can get a 500gb SDD for $40.00 us...
  16. Replies
    20
    Views
    2,010

    Re: All the issues with "i" series ??

    I have V1.6 of the best practice guide dated 08/05/2022 but its to large for me to attach here
  17. Replies
    2
    Views
    415

    [Electrical] Re: Bizhub C759 MFPB reset tool

    Try changing the .pdf to .tar on the attached file. If that doesn't work pm me your email and I will send to you
  18. [CQ] Re: Bizhub C300i Copy from Flatbed and single side adf

    before lifting scanner take off upper left cover on scanner and loosen all screw under the cover on left side then pull up on upper front left of scanner and while holding it up tighten the screws. ...
  19. Replies
    30
    Views
    2,742

    Re: c250i stuck on boot screen

    If you have tried the GXX firmware and it doesn't take it I would start by replacing the CPU board
  20. Replies
    17
    Views
    4,403

    Re: Dead Bizhub C250i after Firmware update Q9

    Its highly advised to update the boot rom before updating the firmware. The machine will let you know if its already up to date. if it does need boot rom updated after it updates power machine off...
  21. Replies
    5
    Views
    828

    [Error Code] Re: Konica Minolta C7000 error code C2814 help

    That looks like the IDC shutter assembly but what is the developer life at? If you aren't a trained technician you could do more harm by just replacing things. Why did you replace drums?
  22. Replies
    2
    Views
    537

    Re: ERROR 4501, 4502

    Was it giving the errors before the write units were replaced? Did you run the adjustments after replacing the write units?
  23. Replies
    10
    Views
    1,170

    Re: c3350i Back Door for Service Mode

    While on trouble screen input stop-0-0-stop-0-1. Then log into service mode
  24. Re: i-Series: Diagnosis and Recovery Tool for boot up issues

    send me model you need it for and your email via PM and I will send it
  25. Replies
    11
    Views
    1,322

    Re: Brand new C450i with 3205 jam code

    We have had several 450i,s that were almost brand new that we tried several things we ended up replacing exit/turn over section to fix it on all of them. KM has really went down hill when it comes...
Results 1 to 25 of 306
Page 1 of 13 1 2 3 4