Try swapping feed units for a test.
Sent from my iPhone using Tapatalk
Type: Posts; User: djs9164
Try swapping feed units for a test.
Sent from my iPhone using Tapatalk
Rollers?
Sent from my iPhone using Tapatalk
My experience with this issue: look at the entrance guide and see if it’s bent. This will cause the paper to enter the ouch unit at an incorrect angle. Check the punch unit to see if there are any...
Most likely toner supply motor black
Sent from my iPhone using Tapatalk
I see this in my schools all the time. The drums seem to pick up moisture. Make sure you use NU Finish, it is a polish NOT a wax. Good luck.
Sent from my iPhone using Tapatalk
This is real common. Humidity does a number on these drums. You need to buy a bottle of NU Finish car polish and buff the drum surface.It will be perfect after that.
Sent from my iPhone using...
I always take a few pictures before I disconnect. It sometimes can help me n these situations. Glad you found it. Keep techin'.
Sent from my XT1635-01 using Tapatalk
If you are talking about the board where the drums/DV units plug in, check out the bulletin or dissambky video at Kyo. That board has to come out to replace the waste assembly and disasembly...
Not the same model but... I took the side door off of a 4002i and somehow the pin on the intermediate male-male conector got pushed more to one side. This gave a constant door open signal.
Sent...
This is not meant to be sarcastic. I have worked on many different models over the span of my career, and Kyocera machines are the most fickle when it comes to reasembly. I often find myself saying "...
So far on the 7052 I have had a high voltage board and a main board fail. Not an auspicious start for me.
Sent from my XT1635-01 using Tapatalk
Kyocera machines have the best warranty in the business. It's a shame you have to use it so much.
Sent from my XT1635-01 using Tapatalk
I have replaced multiple DV units for the same problem in each and every case the user was using some type of cotton bond paper. There is a new style toner exhaust unit that is supposed to have a...
Have you at least cleaned the rollers?
Sent from my XT1635-01 using Tapatalk
This one ended up being the fuser unit. I was reluctant to replace it due to the fact it was recently done. Looks like with Kyocera you can't trust anything. Poor quality control.
Sent from my...
Yes.
Sent from my XT1635-01 using Tapatalk
I have an account with 3 9002i that seem to eat DV units. I have replaced the u it's at least once in all the machines, and now 3 times in one of them. The symptom is always a light shadow which...
Firmware up to date. Checked all my connections. Went through the whole flowchart in the manual.
Sent from my XT1635-01 using Tapatalk
Recent fuser. Checked all connections. Anyone actually replaced the IH unit? Just asking for a friend... Lol.
Sent from my XT1635-01 using Tapatalk
Put th new unit in. Over 2 hrs labor. Did I mention I hate Kyocera.
Sent from my XT1635-01 using Tapatalk
Check in adjustments and see if someone enabled silent mode.
Sent from my XT1635-01 using Tapatalk
Both seem to have the issue.
Sent from my XT1635-01 using Tapatalk
Anyone have a fix for the dreaded grinding sound from a waste toner backed up? I'm getting to hate when I recieved a noise call on this series.
Sent from my XT1635-01 using Tapatalk
This made me more than in non-tech can handle. The boy that controls it is called the container relay board it's located on the right hand side of the machine it's a long narrow board. The connector...
Only comes as an assembly . Wouldn't even try to trace the belt.
Sent from my XT1635-01 using Tapatalk