Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.16 seconds; generated 40 minute(s) ago.

  1. Replies
    5
    Views
    217

    Re: CS 3510i C3300 error code

    I like this one. Perhaps the shading adjustment cannot be successful because of direct sunlight into the scanner cavity.

    On a tangent: I had a Mita many years back that was having continual...
  2. Re: Bizhub c287 - Fans whirring on and off constantly

    The fans are there to cool various parts of the copier as they become hot. Yes, parts of the copier may become hot, even when you are not currently making prints or copies. You should not expect the...
  3. Re: BH-C-284e, offsetting, would love to have an explanation

    Here's my theory, tell me what you think:

    The color toners are layered onto the transfer belt in this order: first K, then C, then M, then Y. Black is always the first layer onto the transfer belt...
  4. Replies
    5
    Views
    427

    Re: FM1-T423-000 adf sep roller issue

    Based on my experience with roller separation systems, I would suggest that there is too much pressure set, pressing the separation roller to the feed roller.

    I am not familiar with the specific...
  5. Replies
    4
    Views
    277

    Re: Hello everyone

    Welcome!! =^..^=
  6. Replies
    6
    Views
    364

    Re: Newbie Checking In

    I look forward to those conversations. =^..^=
  7. Replies
    6
    Views
    364

    Re: Newbie Checking In

    Welcome! =^..^=
  8. Replies
    14
    Views
    983

    Re: KYO Jam Code Quick Reference

    Mr. Synthohol would be very gullible if he handed out his logins to anyone that asked. I am hoping he's a little smarter than that. =^..^=
  9. Replies
    3
    Views
    311

    Re: taskalfa 3500i

    Most often, a piece of plastic breaks out of the rail on the right or left of the paper tray (ON the paper tray, not in the the machine). It's usually because somebody leaned on it while it was...
  10. Re: HP Designjet T7100 paper error occurs

    Did you clean the timing pulley on the carriage motor. I've seen the rubber shavings from the old belt pack into the grooves of the timing pulley, making it slip. I don't think that I've ever seen a...
  11. Replies
    5
    Views
    2,898

    Re: Accurio c2060 error c2221

    Determine which drum fits too tightly on it's drum shaft. In my case it was 3 out of 4. Install only one drum, then close the drawer to see if it closes properly. Remove that drum, then try the next...
  12. Re: Toshiba 385s invalid factory configuration problem

    Could it be that it had a Lexmark toner cartridge installed, not a Toshiba cartridge? Or vice-versa? I'd think the EEPROM would be coded differently. The reset may have changed the manufacturer to...
  13. Replies
    6
    Views
    590

    Re: Bizhub C250i poor fixing

    There certainly isn't a lot of detail in that bulletin. It would have been nice to know what changed. Or would that be too much like admitting there was a problem? =^..^=
  14. Replies
    9
    Views
    1,096

    Re: Calibration Toner-Banding on paper edge

    Your welcome. Sorry I missed your post on the first go-round. =^..^=
  15. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    The cyan & magenta developing units are the only thing it needs..

    Yes, I reduced the resolution on my camera phone so that the pictures were 1MB or less, then they upload just fine. =^..^=
  16. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    Sorry, no DIY fix. Those developing units are glued together. I have tried disassembling a few units, but just ended up with broken plastic. The other machine would use the same spacers, but there...
  17. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    The cyan and magenta developing spacers are bad. AFAIK the only way to get them is on a whole developing unit assembly. This was a common flaw on this series. =^..^=
  18. Re: Toshiba 385s invalid factory configuration problem

    This is a Lexmark rebadge. Check that the toner cartridge contact set is not broken or damaged. =^..^=
  19. Thread: Biz754

    by blackcat4866
    Replies
    6
    Views
    634

    Re: Biz754

    This is the one I thought of. WSD does not function reliably. Choose a static IP in the driver. =^..^=
  20. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    Those rollers look VERY worn. I'd start there with new rollers. =^..^=
  21. [Misc] Re: Printer APIPA IP question - Is this printer acting as a server?

    OMG. I can see why it's useless. It might work in an isolated situation where a printer is plugged directly to a laptop with a cat5 cable, without the benefit of DHCP it could choose an off-range IP....
  22. Re: kyocera taskalfa 3051ci Cassete 2 does not work. no paper level. only size ID.

    The paper does not look like it is loaded properly. My suggestion is to:
    * remove all the paper from tray #2
    * perform a U906 partial reset to clear out the lift error.
    * load a small amount of...
  23. Re: ECOSYS P2040dn showing Call Service 2000:0006256

    Hello Hans.
    2000:0006256
    You can disregard the part after the colon, that's the copy count.

    C2000 is a main motor error (not rotating). Something is seized and won't allow it to turn, possibly...
  24. Replies
    5
    Views
    603

    Re: C458 rainbow effect scanning

    I agree with this one. Konica Minolta CCDs that do very long scan runs are well known for failing on the 654e series, and 808 series. Usually they store errors that auto-reset, but come back more &...
  25. [Misc] Re: Printer APIPA IP question - Is this printer acting as a server?

    Just for us dummies: What is APIPA? =^..^=
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4