have played with this special oauth firmware on my c3350i and can confirm that it works as expected. Saving the login token via the web browser. A shame it is not going to be made standard because it...
Type: Posts; User: EarthKmTech
have played with this special oauth firmware on my c3350i and can confirm that it works as expected. Saving the login token via the web browser. A shame it is not going to be made standard because it...
I'm having a number of these trays all with the 1740 jam from tray 4, the accessory version and the standard version on C750i now, its not jamming or slipping on the paper. The actual transport motor...
been using adblockers for years, hard to beleive people tolerate the number of ads out there these days. Youtube is the worst now, unwatchable without it.
In addition to the mandatory duct...
if network settings initialised packet filtering is enabled by default (in my marketing region anyway) and if what you are connecting to it from is on a different IP range this will give you these...
Exit assy's are very common to squeak on the sparrow series, and also not hard to lube all points of friction with a suitable plastic compatible grease. Once done correctly its generally not an issue...
I've seen near new SMD capacitors dead short after some time in operation. I've had other boards with this issue, including with vapourised tracks because the load wasn't enough to put the psu into...
had this a few times - if its not the sensor inside the front left (either contaminated or faulty) that is activated by the actuator rocking on the cam lobe on the side of the box, it is usually the...
this is always a TCR issue. Older firmware has the no paper recognised in the tray bug when the TCR abnormaility happens.
Check TCR levels, guaranteed once of them is low.
Usual issue on these...
check cyan led erase array. If one LED is dead shorted (wired in series) and not illuminating, you will have a continuous ring of non erased garbage.
C750i drums are notorious for squeaking.
I've seen the black drum blade overheat and flips / stops cleaning properly on machines doing thousands of pages in a single run too. (c750i)
This is exactly the issue, annoyingly, several machines have done it a second time and no mention is made of the lot number of when the pcr rubber composition changed. So we are just left to hope for...
I look after multiple remote locations and minesites - this one is equatorial and has 90+% humidity every day of the year with constant temperature that never changes. It is not at all dirty all...
It's not supported - but it does work. I have a C250i with FS-534SD at home, all functions work as expected.
You must NEVER update the firmware with the unsupported FS-534 finisher plugged in or...
to use a used panel as a new one involves modifying the data stored on the serial eeprom on the panel board. Not rocket science but not in the scope of what a technician should be playing with.
The standard things to check for this, including on the Colour versions of this engine, C659/C759
1, ensure duplex gate lowest point is 34mm off the table when measured outside the machine ( no...
On the filthy minesites i look after, my above mentioned mod has been a hit. Every modified machine with lessened spring pressure on that stupid retaining hook has never had the issue again. I'm...
is this simply for removing stuck / old API installed from the machine? you have been able to do it at the control panel for some time now.
don't be so sure about that... Nothing that large, only desktop's.
Replace the flat bed scanner.
Its actually a very easy task and takes me about 15 - 20 minutes with an electric screwdriver. I take photos of the scanner adjustments from the donor machine before...
Yep +1 this
Seen this plenty when people try lifting open the jam access door without unlatching it. This is a 100% fix.
Also helps with the 6633 jams resulting from insufficient separation...
Anyone else dealing with this?
Replacing the pickup assy is a quick fix, though expensive and it only lasts a few thousand pages before it starts again.
Trimming 4 loops off the hook spring...
When printing smooth transitions from light to dark in any colour there is banding in any mode other than plain paper mode on all I series color.
It matters not what driver is used, windows and...
Looks a lot like an end user.
New account, first post, extremely basic issue.
4 / 4e series remove and destroy ssd module
8 series remove and destroy emmc module
Older - remove and dispose carefully the nvram module (lithium battery caution)
Print quality is miles better on the older engines too. People want to pay as little as possible for the machines though, so this is the end result.
I saw an old c452 recently on a minesite full...