My goal is to do this process on the mp c2003. I have the firmware but I don't have dummy48.pat 1dinstall sistem.rom and install.cnf
Type: Posts; User: joserf
My goal is to do this process on the mp c2003. I have the firmware but I don't have dummy48.pat 1dinstall sistem.rom and install.cnf
Sorry, I mean the file B2215601F_1
55417
Could someone get me this file?
[QUOTE=MitchD;708791] Estoy luchando contra un problema muy grave y espero que me puedan ayudar. Es un c6502 con SC672-11. Hasta ahora, he reemplazado el panel de operaciones, la PCB de control, la...
[QUOTE=luca72;2202691] Entiendo, este pdf es para una máquina antigua, en esta serie debe copiar solo "systemcopy" en la tarjeta SD, en la carpeta romdata, pero no recuerdo la secuencia de teclas que...
54516
I do not have access to that platform, if someone could access
This is what I mean but for the 2003 mpc. I would only need the procedure
54514
This is what I mean but for the 2003 mpc. I would only need the procedure
Hi Luca, I tried what you told me about the switches and nothing. Then I tried to clean the entire plate and neither. Regarding the hard drive, I will keep it in mind for future plates.
[QUOTE=GIUBOSS;2202139]No empeoréis las cosas, era para quitarlo y no para añadir uno. Intente según lo sugerido por Anothertech, en caso de que formatee el hd y vuelva a cargar el fw, infórmenos [/...
[QUOTE=slimslob;2201548]Compruebe que no haya ningún pin doblado en la NVRam y que no esté girado de forma incorrecta. También verifique que el cable USB del controlador al panel de control no esté...
Thanks for your answer ! But he didn't have a fax and I installed one for him out of curiosity but nothing
Thank you very much for your reply Luca! Tomorrow when I'm in the workshop I'll check what you told me
I have a problem with this model of machines that I put a new nvram in and suddenly the sc 672-11 jumps out. I have changed all the ipu, bcu, ctl,cables, screen. Main ctl led 1 is constantly on....
Of course I was referring to that ... I have not specified well ... it was my fault ... I'm sorry
thanks to a user ..... I have requested this information .... it has been misinterpreted what I was asking ... I'm sorry
Hello,
You must make a Data Clear + Format HDD.
1. Go to the Service menu> System 1> Initialization> Delete all data and then the blue key.
After doing so, disable the HDD, then re-enable it from...
friends just needed to know information on how to reset the information on the machine not to change the counter of the machine .... I'm sorry if you misunderstood what I meant
if I was referring to the lanes where the lamp and the crystals are ... if the adf has had weight on top you have to put it back again, taking it from where the glass is and pushing it up with your...
you have the bulging adf ... you have to take the exposure glass and put it horizontally ... the adf car is uneven and it creates shade ... there is also the option of dirty glasses but it misses me...
you have the bulging adf ... you have to take the exposure glass and put it horizontally ... the adf car is uneven and it creates shade ... there is also the option of dirty glasses but it misses me...
that's the solution .... change plates no man hahahaha
the machine stays loading the system but it does not start at all ... in the model 284 with the recovery data I can recover it and start it. It is as if I had lost all the values and could not...
I would like to make a factory recovery of the machine ... in the series 284/364 is how it is done but in this model
hi people I need to know what procedure you have to do a recovery data in these machines ... if someone could help me I would appreciate a lot ... thanks