Be better if we know what email you are using like hotmail or office 365
You also need to input your DNS
IP details in the machine as well
If you haven’t done so already
And make sure your...
Type: Posts; User: bmwmick
Be better if we know what email you are using like hotmail or office 365
You also need to input your DNS
IP details in the machine as well
If you haven’t done so already
And make sure your...
Only if you don’t do it your self which is easy
Just format the Msata and clone if a other machine of same model
Or if you copy each model when you get a machine in to your laptop
It’s easy
...
Yes I have bought a new one for the copiers
I was just going to use it for the car
If it was a easy repair
Sent from my iPhone using Tapatalk
3M vacuum need part number for motor or carbon brush set please
Sent from my iPhone using Tapatalk
By default it only prints out when you have a error
To change this you have to change the soft switch in fax settings
So you need to check these
Sent from my iPhone using Tapatalk
That service mode will reset all the data back to factory
And delete the address book
Sent from my iPhone using Tapatalk
Swap black drum unit with cyan / magenta and see if fault
Swaps to this colour
Then it’s drum blade
I did not do the data reset
But I did not see any network reset just as photo
Sent from my iPhone using Tapatalk
Hi Guys
Still having problems with not seeing network settings https://uploads.tapatalk-cdn.com/20200826/a2ea722edf0cd262a86810a1e19542f0.jpg
...
Thanks guys for all the inputs
I will give that a go
Been a copier engineer 36 years
Memory not as good as it was
Sent from my iPhone using Tapatalk
Hi guys
Thanks for reply’s so far
There is no model on front door
Just a label with the name
Develop
So I will remove this and see
What it is
As it’s been rebadged
https://uploads.tapatalk-cdn.com/20200820/d7b9e2693560f678622526f8efc81f04.jpg
Sent from my iPhone using Tapatalk
On config page it’s says
Generic 20C-4
Sent from my iPhone using Tapatalk
The network settings are missing
No option 5 on bizhub 20C-4
But network config shows
IP address 192.168.1.200
When network cable is plug in I have green light and flashing green light as if...
Does anything turn at all when you first turn the machine on
As I have the power supply cause this fault
Not on this model though
Sent from my iPhone using Tapatalk
Also try new network cable
Had problems similar and that’s what it was
Sent from my iPhone using Tapatalk
Have you set up all the network settings in the web browser of the machine
IP address
Subnet
Gateway
DNS if I had problems I would use 8.8.8.8 for this
Your SMTP setting to send email
...
No you don’t
All you need is same model of machine copy the M-Sata card
Format the M-sata in the machine you don’t know the password for
and copy file over to the M-sata from working machine...
You have cleaned the optics and each side of the lens unit ?
Sent from my iPhone using Tapatalk
You have to replace all the boards
Why would want to remove the DSK kit ?
Sent from my iPhone using Tapatalk
That’s the password for web with capital S for the machine it’s
00000
Sent from my iPhone using Tapatalk
To check that it is the clutch
Make 15 B/W copies or prints and see it you get the code
If you do it’s not the clutch
It could dirty PTC or high voltage board
Sent from my iPhone using...
You get this code when printing pdf when you use edge
Use chrome or Firefox
Should fix the problem
Sent from my iPhone using Tapatalk
The newer machine use a photo sensor on the right hand side for when the waste is full
So how would you know
If the waste was full on the older model ?
Sent from my iPhone using Tapatalk
Never had to fit a board for this fault
Sensor on the pick roller yes
As this is what tells the machine to start lift motor
Or the arm on the back could be broken that brood the pick up roller...