Search:

Type: Posts; User: C47Sys

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Hey Phil I'd like to thank you for leaving your valuable reputation comment on my profile, another fun fact for you I purchased genuine canon heads you genius
  2. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Thanks Cedar I'll take a look and see what I can find, this is exactly what I was looking for. Finally some good advice! As someone who both repairs these machines professionally AND also runs the...
  3. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    I'll listen to advice that doesn't complain about the 3rd party ink, I have no argument that it can be bad or isn't as good as Canon ink. I fully understand that it can cause issues and if the issue...
  4. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Aww what do you expect me to reply with? :D I have no reason to be sarcastic except when being told I have no experience, don't know what I'm doing and having my one question ignored because I'm...
  5. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Thanks for your valuable and helpful input and your dislike for the ink ;) you're what make forums like this an excellent place to come for assistance.
  6. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Hi unfortunately no it did not come with any firmware disk, the old head which I do still have is unfortunately leaking from around the baffles seal. Basically the head assembly has a little plastic...
  7. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Fabulous Phil so basically because we're not wasting money on genuine cartridges to see if we can even get the unit running you provide no help? I understand how the damn priming system works fun...
  8. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Ok great I appreciate the feedback on the non-genuine ink.

    However as I've already mentioned, the printer HAD genuine ink all of if it was genuine. Then the printer attempted it's wonderful self...
  9. Replies
    19
    Views
    4,606

    Re: Canon ImagePROGRAF 8100 PHeads Wrong Position

    Well unfortunately I'm not about to waste literally twice as much on Genuine canon ink when they design it to literally just dump ink over and over to attempt to clean the head. In any event the...
  10. Replies
    19
    Views
    4,606

    Canon ImagePROGRAF 8100 PHeads Wrong Position

    I'm ready to push this thing off the top floor of the highest building I can find in town. No clue why in their infinite wisdom, other than its a money maker (good luck because I'm buying 3rd party...
  11. Replies
    14
    Views
    5,387

    Re: Bizhub C452 Outfeed Paper Jam

    Problem solved I went to remove the bridge unit and did actually find a loose connector and now there is no longer a jam
  12. Replies
    14
    Views
    5,387

    Re: Bizhub C452 Outfeed Paper Jam

    There is just one connector from the finisher to the main unit, none of the pins seem to be damaged or bent.

    The error code is 72-16 with jam locations 13 and 31 43692
  13. Replies
    14
    Views
    5,387

    Re: Bizhub C452 Outfeed Paper Jam

    With the finisher disconnected / removed from the unit it'll still jam in the same position. I'll check about the bridge unit
  14. Replies
    14
    Views
    5,387

    Bizhub C452 Outfeed Paper Jam

    I've got a Bizhub C452 that consistently jams at the same output point. I've attached a picture of where the paper gets stuck every time. When copying a single page just one paper gets stuck at that...
Results 1 to 14 of 14