Change the scan settings from Photo to Auto color setting.
Type: Posts; User: RMC8112
Change the scan settings from Photo to Auto color setting.
I have not used the Scan to Folder tool, but i always setup my scan to folder manual way. I add a user on the customer's computer as Scanner and make it an administrator. Then create a shared folder...
This is from the fusing unit. Check to see if there is a Cleaning mode on the printer. This will clean the fusing unit. If not, replace the fuser. This happens when you run cardstock and dont change...
Check the flat cable going from the formatter board to the controller board. You may need to replace it (
CF388-60116). One of the leads is folded over or not making contact.
Check the hard drive. If its a Toshiba, then replace it with a Seagate (L41606-011).
Try doing a PH cleaning. if that dont help, replace the PH.
I have a M477 that after replacing the fuser for damaged fusing film, when we print the demo page it comes out with no black. Also as the printer printed, i heard the developer motor making a...
do a test print and then open the toner door as the paper goes into the fuser. If the void is not there before it gets to the fuser, then its the fuser. But i think its the developer unit. Get a...
Checked the HDD is its a Toshiba. If it is, then replace it with a Seagate (L41606-011), then reinstall the firmware. that will restore it back to factory.
I had this issue before. I just increased the scanning DPI from 300 to 600. that slowed it down.
Check this out.
https://laserpros.com/img/TechTips/hp-cp2025-cm2320-m351-m451-m475-m476-cleaning-mode-misprint-error.pdf
Service Menu Pin Codes
HP Printer Model Service Menu PIN Code Menu Access Code
There is a notice on the TSRC about SC819. If the Toner Gauge app is installed, then you need to uninstall it. Go into the SOP system settings by doing Reset-> 806182-> #-> # -> hold Clear for about...
There are two ways.
1. Logon to the WIM as Supervisor.
2. Enter Factory Mode
Reset->143->Clear ->Clear Hold on second Clear
The screen will change to SP screen.
Click System and...
I got an account that has a MP C3504ex and ive hade to replace the yellow toner hopper 4 times in a year. Last one lasted about 3 months. I know the fix according to Ricoh is to replace the hopper...
Looks like a transfer roller issue. I would check the contacts for the PTR, also the shaft for any dirt that will prevent contact. check for cracks in the roller foam. i had an issue like this and...
I would check the laser unit. there is probably dirt on the glass or lens. I would also remove the laser unit and clean it that way.
That a Laser Unit issue. RM2-5528
Here is the page from the manual. Looks like you may need to follow step 6.
4. Troubleshooting
► Error Code
U1–2141
U1–2142
► Error message
Fuser Unit Failure: #U1-2141.
Fuser Unit Failure:...
Has anyone came across this? I have a customer who has this on their IM C3000. I've replaced the BICU and the BCU, but still getting it even after resetting the SC code. When I go into SP Mode, i can...
Did you try cleaning the LSU glass?
There is a Tech Bulletin about this. Update the LDCD firmware.
50216
I had something like this happen to one of my customers. Turn out to be the transfer roller. The foam roller was cracked. Once i replaced it, it printed perfect.
Ive seen this before. Check the drum unit, and charge roller. The cleaning blade for the drum has something stuck and is wiping the toner from the drum. When i had this happen to my customer, i took...
If you look where the originals exit, there should be 2 black belts or bands. I had to replace the whole ADF section to fix that. There is no part number for just the rubber belts. Part no....