Thank you very much.
Perhaps the problem was caused because the machine was unplugged 1 or 2 weeks.
How often or when do you think the problem will appear again.
Type: Posts; User: i-have-fax-problems
Thank you very much.
Perhaps the problem was caused because the machine was unplugged 1 or 2 weeks.
How often or when do you think the problem will appear again.
I've cleaned this printer for a customer (corona wires and pick up rollers nothing more). Now he brought the machine again
and said it has no power. I've plugged it in and it works.
After several...
Do you know the problem, that sometimes you have quite much
toner spilling on the left side of tonerbox, so the drum unit gets
quite dirty on the left side.
But drum and toner are original.
What...
Hello,
I have an older MS510 which shows time input after every power on.
Is there a battery which is defect or what can I do. All other data are
not lost only the time must be set, which was...
Dear colleagues,
there's a problem with toner residues on the lower fuser roller.
I had this issue with a black/white machine and you can change the fuser mode from 1 to 2 in the settings....
Dear colleagues,
one customer asked if KM i-series have the OAuth Function (for scan to email)
Now, as you may know there is the special firmware GP4-and so on
which should support OAuth 2.0....
Hello,
could anyone tell me please, which sensor the jam-code U18 183f0000 refers to?
Or what could the reason be?
No paper jam in the Scanner and all Sensors are clean.
Thank you.
Sorry I've forgot to say it's a P3155.
Hello,
is there a possibility to reset the display message without that the printer will do
a installation routine. I know when I press "new drum" in the menu the printer resets it but makes
a...
Smearing and often jam at the same position. Paper has left fuser and leading edge is 5 inch or so out of the exit section.
Thanks.
60759
Yesterday I was there and first I printed the counter list. No noise. Then I printed the c-m-y-k gradiation pages (all 4 in one step you know). With cyan, yellow and magenta noise was there, with...
Has anyone heard this noise:
https://www.youtube.com/watch?v=CVdAg1ke-e4
High Frequency. Customer says it only happens with duplex print. But I'm not sure.
Oh sorry,
please delete this thread.
I've found it here.
Dear colleagues,
a customer who has other devices from us just asked me if we could
look after a ir 2030 or C2030i (not sure) with error code
E0000740000.
What could this be?
Thank you.
Sorry, I don't know. I wasn't there. Only talked to customer on phone.
But what if it is OEM?
Dear colleagues,
a customer told me that his P3045 has become so slow.
He prints about 300 pages at once and now it takes twice as long.
Longer pauses between the pages.
Printer is 5 1/2 years...
Thank you.
Parts of the black foil are missing, are torn off.
Hello,
we have a customer who prints about 2000 pages per year with this printer.
Now the fuser unit is broken the second time in this printer.
First at about 2000 pages then now again at about...
When you switch the printer on
it hangs at Initializing.
Has anyone had this problem.
What can I do?
There was/is a Konica-Minolta document with the description how to set up Scan to SMB.
Does anyone have it?
I think, in this document, it is said that it must be a local user for scan to smb, a...
Thanks.
It occurs with single and multiple prints.
With black toner system I meant when the drive mechanism of the black iu
is involved. But I'm not sure.
Ok I could replace the whole exit...
Here's a little video of the noise,
but don't think it only occurs when paper is ejected or transported.
This morning I switched the printer on and at warming there was a
short little squeak...
I guess there is something wrong with the fuser.
Isn't there a general problem with the fusing unit
of this series?
What can I do?
Thank you
Dear colleagues,
I have a MX510 which makes pale copies and scans.
I've cleaned the optical unit from inside, I've replaced the CIS Assy (copy became even paler)
(ok the inserted one was a used...
Hello,
I have a Tally Printer T2150 which makes a rattling noise during start up and some gears move back and forth then.
Then it reboots and a Hardware Error +0310 +000--- 000128 +0304 is...