Search:

Type: Posts; User: Dcopyman

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    480

    Re: Sharp BP50C26 with code C1-14.

    Any update on fix yet? I have the same error on same machine that was in storage for a bit then moved to new location, and since then has had a hard failure c1-14.
  2. Replies
    5
    Views
    1,275

    [Error Code] Re: MX-M904 ERROR L4-31

    i think the pwb you're referring to is the sub AC PWB
  3. Thread: sharp mx3050n

    by Dcopyman
    Replies
    13
    Views
    2,910

    Re: sharp mx3050n

    Check for paper clip that falls on adf pwb. This causes weird issues
  4. Replies
    10
    Views
    1,398

    Re: MX-M365 black lines

    Charge unit or transfer roller swapped out? It REALLY looks like the drum blade is not cleaning properly, Is it brown instead of clear?
  5. Replies
    13
    Views
    8,223

    Re: Sharp mx 6071 h5-01

    I had this on 2 machines like that... Check voltages from wall..... both of the ones i tested had bad voltage drops.... do you have ESP boxes on all the copiers?
  6. Re: MX-C401 APPD1 N jams on 8x14 when duplexing only

    Make sure the delivery guide isn't broken !
  7. Replies
    8
    Views
    1,185

    Re: PPD2_FIN - MX-M565N w/FN11

    Replace clutch on upper right back side of finisher.. this has fixed over 10 machines with same issue
  8. Replies
    13
    Views
    8,140

    [Jamming] Re: Mxm565 build up on fuser guide

    POD1 Jams due to Toner Adhesion to Fuser Guide Plate
    Bulletin Number: TT-102517_1
    Models: MXM364N, MXM365N, MXM464N, MXM465N, MXM564N, MXM565N
    Date: 10/25/2017
    Priority/severity: Medium...
  9. Re: Sharp MX-M465 toner on fuser entrance plate, flaking off

    POD1 Jams due to Toner Adhesion to Fuser Guide Plate
    Download




    Bulletin Number:
    TT-102517_1
  10. Replies
    9
    Views
    1,642

    [Electrical] Re: Showing N9 on ESP surge protector

    Actually on Newer Sharp copiers, anything over .5VAC is too much between neutral and ground
  11. [Error Code] Re: Error F2-73 immediately after memory clear sim88-01

    I would try sim 16 if doesn't fix ... replace PCU PWB... just curious why you did sim 88-01 in the first place?
  12. Replies
    9
    Views
    1,642

    [Electrical] Re: Showing N9 on ESP surge protector

    Installed a Tripp-Lite LC2400 today..... we'll see if it helps with the power issues!!!!!!!!!
  13. Replies
    10
    Views
    1,207

    Re: Sharp MXB402 - Paper Jam/New Fuser Unit

    Check sensor for registration unit..... Behind PS unit... what jam code is it showing?
  14. Replies
    20
    Views
    2,719

    Re: MX-M5050 print quality

    The quality is USUALLY great on these models.... Your quality isn't normal ! I would check your Sim 46 settings and see if anything is out of setting
  15. Replies
    9
    Views
    1,642

    [Electrical] Re: Showing N9 on ESP surge protector

    kdr636.... Do you have any first hand experience with either one, and if so which would you say does the job better? I looked up prices quick and found one was around $162 msrp and one was $562 msrp....
  16. Replies
    9
    Views
    1,642

    [Electrical] Re: Showing N9 on ESP surge protector

    Yes I tested with meter (crappy one) under stress and so did the Electrician.
  17. Replies
    9
    Views
    1,642

    [Electrical] Showing N9 on ESP surge protector

    I have a MX-5070N that is powering down and restarting frequently. I have replaced Msata, and installed an ESP surge protector. The ESP displays N9 ( >=4vac between neutral and ground) and also...
  18. Replies
    5
    Views
    2,014

    Re: Sharp MX-6070V with the COVID Curse

    had the same problem and new PCU pwb fixed issue also
  19. Replies
    14
    Views
    6,940

    Re: Are F2-64 a common problem with Sharp?

    That model is very prone to that error code... Check the lower holder for black toner motor... sometimes plastic clip breaks and motor can seperate from drive not allowing toner to be added... after...
  20. Replies
    3
    Views
    708

    [Dead] Re: MX2630 switching itself off

    Sometimes a corrupt print job can cause machine to keep cycling on and off, try disconnecting network cable and see if that corrects issue
  21. Replies
    8
    Views
    2,534

    [Error Code] Re: LCC_ERR error on MX1054 with LC13

    we have been using the ESP brand also for 10+ years
  22. Replies
    8
    Views
    2,433

    [CQ] Re: Color stripes Sharp MX-3060 and MX-3070

    Sounds like high humidity causing arcing inside copier..... Sounds like customers need to control the humidity better at locations
  23. Replies
    8
    Views
    2,534

    [Error Code] Re: LCC_ERR error on MX1054 with LC13

    JLSam.... no other jam codes or errors have accompanied this error.... i thought power may have been an issue also, but they recently moved to a different location that had a dedicated 208v for...
  24. Replies
    8
    Views
    2,534

    [Error Code] Re: LCC_ERR error on MX1054 with LC13

    And yes the Firmware is updated to the latest version that was supposed to fix this issue!!!!!!
  25. Replies
    8
    Views
    2,534

    [Error Code] LCC_ERR error on MX1054 with LC13

    Replaced LC13 main pwb and power supply PWB, Replaced all 4 clutches in lc13 per Sharp support, also replaced sensor that detects lcc and copier connected, and replaced 1054's PCU PWB. Machine will...
Results 1 to 25 of 34
Page 1 of 2 1 2