59896You have to choose the right model under settings in the configure tab or it won't work.
Type: Posts; User: HuronMan
59896You have to choose the right model under settings in the configure tab or it won't work.
Check for bound up bushings in the reverse unit.
It's probably a consumable has reached end of life. If you don't have a login for Papercut, touch the menu button. You should see a exclamation icon in the upper right. Touch that and it should tell...
Here's a Papercut/firmware matching guide. Authorized Solutions | Konica Minolta bEST Technology Suite
I have a t930 with a reseat print head message. The customer ordered and replaced it with another ph and has the same message. I went out and noticed the cyan ink was out of warranty\expired....
Sticks and stones...
https://youtu.be/E5pZ7uR6v8c
Looks like that's the fact. We just took over service and supplies for these. I'm not sure yet what we send them.
I went back the try your recommendations and try the disable cartridge check in diag mode. They didn't have another toner to try. But today I reseated the connectors on the driver pca board and it...
I have a HPCLJ3600 that's throwing a 59.51 code. Removed r side panel and the cyan motor isn't turning. I swapped it with the yellow motor and cyan still doesn't turn. The manual I downloaded from...
Try the torque limiter on the double feed roller. Also, check that the rollers aren't breaking loose from the hubs.
Says scanner error 13 on display. 3957339572
And yes, it's a guess. I've recently been forced to service these.
I have an HP mfp477fnw that displays a scanner error 13 when its powered on. I've done the hard reset and it's plugged directly into an outlet. I reseated the ribbon cables from the scanner to the...
I've been unplugging these so they are always driving the auger. If it still doesn't drive, there is a 1way in the drive unit on the shaft that drives it. Remove the carriage, reach in and grab the...
Hey Now,
So I have a bh364e that has, in the last few days, started throwing T81's when you try to send a fax. I get a dial tone at the machine but when you hit start, it scans the orig. and...
Did you try a different paper tray?
turning the loop to a negative.
I had to flash one of these things to get rid of the b003's, a couple of weeks ago. I tried 3 different drives. A 2G and 2 16G's. I went and bought a new Sandisk 16G and it finally worked. I dunno.
The biggest help on a VOIP system is to turn off ECM. Go to tech mode, soft sw. 041, bit 6 and make it a zero. You can see if that helps. If not try setting sw's. 048 to hex c6
049 to hex 05
050 to...
It's the mfbs board.
I had either a c451 or c452 blowing the customers wall breaker a couple of years ago. I tried a fuser and the coil but it turned out to be the fuser heating coil driver board.
Hello,
I have a customer that ordered an LU-204 for his BH552. He ended up not wanting to install it on the machine and I guess our company won't take it back. It's the one that will feed up to...
Hey Ya'll,
I haven't tried to replace a 423 roller yet, but I have ordered the di3510 uppers(4030570103) and use them in the bw200/250/350's. Seems like it should work for the 423. Working for a...
The other day I had a 452 putting a crease on the front of 14" and 11r out of tray 2 because the side guides slid all the way to the back. The physical centering adj under the lift plate. Maybe yours...
We went back with a pwb-a board. It didn't fix it. Gunna try flashin it and mfbs.
I just had to make a bh250 do this today. It has a jam indication that I can't get rid of and is unusable so I unplugged the duplex unit and got the screen you posted above. Now it at least runs 1...