Thanks Kiran,
i searched in the old stuff for an ide hdd but they were all broken, but i remembered i had compact flash to ide adapters with 8gb cards, i uploaded the image and it worked.
I hope...
Type: Posts; User: Massimo Italy
Thanks Kiran,
i searched in the old stuff for an ide hdd but they were all broken, but i remembered i had compact flash to ide adapters with 8gb cards, i uploaded the image and it worked.
I hope...
Hi guys,
i have a formatter card dj800ps with hdd dead, anyone can help me?
i need the hdd image and instruction to copy to new hdd.
thanks in advance.
Massimo.
sorry, but why open new treads on topics already discussed?
I suggest using the search function before open new tread.
It is not a problem of brand, but of characteristics.
Each brand has products that are more suitable for graphic printing.
You have to select among these.
Hp, canon or epson they have products...
That plotter is not suitable for poster prints, but cad drawings with some images.
Has small and expensive cartridges.
If your client makes occasional prints it might be okay, but keep in mind that...
Dear guys, thank you all for the support.
The problem is solved ... and the story, for the moment, it seems over ..
I thought about it a lot, this morning I tried to insert some shims in...
If they are the same, now I don't remember, you can try to invert the toner hopper with the magenta one for example, and if it happens again on magenta you will know that you have to replace the...
The belt is new, frankly I do not observe any particular hopping, but I want to move the motor downwards just to give more pressure to the belt and consequently to all the carriage.
Now I do, I'll...
Hi Kiran,
I cleaned the axis and tried various lubricants, Teflon, for weapons, in short, nothing pasty, the carriage runs without problems or friction.
I am thinking of lowering the motor...
Hi Hook,
I'm happy to have fans, I just hope this story is successful, and doesn't end with the plotter's defeat or mine.
Seriously, you have made a pertinent observation, I do not observe any...
Finally the bushing arrived, I mounted them and the problem is exactly the same!
The engine remains to be replaced, but is it possible that it has no problems at low speed and when it turns faster...
I have never replaced the tubes on those models and am not aware of the situation.
But take the time to do it calmly and you will complete the replacement.
In fact, you have air on both sides, but considering that the head is empty or almost empty it may be that the air is coming from the head. however it is the replacement of the tubes is the best...
personally when the tubes have problems I have always found physical breaks near the terminals, with ink leaks. in your case it is evident that there is a leak but difficult to locate, perhaps in the...
But was the leak test ok when the old priming motor was still fitted?
Certainly the drop sensor cannot detect anything if the ink does not come out of the head, the only test would be to mount it...
Perfect comparison !! compliments.
5% of the hard heads remain, but we will convince them too!
if the leak is at the base of the cartridges, consider that the air may have also entered inside.
difficult to verify.
but if that's the case it's not good,
normally they are vacuum bags.
some...
From the manual....
----------------------------
Purge Tubes
NOTE: Make sure that NEW Ink Cartridges are installed or that the ink volume remaining in the Ink
cartridges is above 60cc before...
usually the tubes leak ink when they have problems, you have an air intake which is a different condition.
Is there air near the ink tanks? in this case, the seal of the connection between the...
it seems a puzzle to me to understand the meaning of those combinations .. I wouldn't worry at the moment, since the board has already been replaced
start replacing the pumps, and see the difference...
since in the past you have helped this user to donwgrade the firmware, maybe mascopia could try to send him a pm, even if he is no longer active since 2016, he could receive an email and reply.
Sorry, I realized that the translator has not done his duty, I meant if you can try to replace the entire transfer belt unit, perhaps with a unit that is working on another machine.
I would check the transfer belt, maybe if you have a try to replace it and see if the defect goes away
I am not surprised that these machines are still in the field today, if panasonic had believed in this sector today it would be a leader .. but let's get to the problem .. frankly I don't remember if...
Welcome