When you install a device via USB it will run on different drivers to if you install it via Network.
Solution is to install the printer to customer computer via network cable directly and add device...
Type: Posts; User: Crowfeather
When you install a device via USB it will run on different drivers to if you install it via Network.
Solution is to install the printer to customer computer via network cable directly and add device...
Ecomode is your friend.
Replace your shonky yellow toner with something decent.
If its not a consumable out flag, then you will need to get a copy of the service tool to do some diagnostics.
If the printer has a syncthru page you could try accessing that for alert information.
If you've replaced the fuser unit, and no paper is jammed in an area to flag the thermistor, then look at the Fuser PCB or Fuser Motor.
Perform manual calibration.
If problem persists do a jam test.
If jam test shows complete image on drums, then check transfer mechanism is sufficiently pressurized.
If jam test shows incomplete...
Sounds more likely that the internal assemblies are not sufficiently pressurized. This can occur if the chasis is bent (damage in transit), or if the assemblies on the rear door are not properly...
Do you get the same problem if you power on with no cartridges installed?
If you hold down the cancel button for a couple of seconds, with the toners installed it should start trying to print...
You can install the X4 or X7 series drivers as they use the same architecture. The CLX-9301NA closest brother is the X3220NR, but the X3220NR uses different architecture.
You could be getting the...
If you want something super reliable then the MF742CDW
If you want something that is okay, and cheaper on the ink a Samsung C480FW or CLX6260, all alternatively some of the Kyocera ecosys have...
At this point why not just use Papercut NG. Its a free solution if used in this limited way.
I always thought tiered coloured billing was to up the price, because whether your doing 1% or 10% your still running out the life on your maintenance items.
However, if customer is doing 50%...
There are a lot of Print Management systems from an MPS perspective that allow you to manage the whole works from ticket raising, stock holding, readings etc.
Dyalog is one example of this that...
Sounds more likely they just wanted to reduce manufacturing costs of shipping two identical boxes with different brands and, no longer have to stock two different lines of product within their...
The manual you are reading is incorrect, the A1-4111 and A1-4112 are actuator motor errors. Very common error on the Samsung A4 kit, and is resolved by replacing solenoid/main drive unit. A quick...
If you get this ever again, just do a calibration with calibration sheets (essentially white card). It is stated to do these calibrations (shading and position adjustment) when replacing ADF, but...
The A1-4111 and A1-4112 errors are to do with the solenoid/main drive unit. Actuator motor failure is the message. No idea how you are getting feed motor or Main board from that.
Remove and re-insert LSU.
If issue persists, check the ACR report.
Just do a system rebuild.
If there is no option to setup SMTP for inbound then just download a free NG license of papercut, max 5 users/printers and supports email to print.
Either you blew the HVPS or you cabled it wrongly. This is happening as the imaging units are being sent too high charge.
Your original problem could be down to paper rather than fuser unit being...
Many manufacturers do this already its not just a HP thing. They will serapate 40PPM upwards from 20-40ppm machines. The 20-40ppm will all be almost all identical, and the 40-60ppm will be almost all...
The printer draws an image internally on the ITB Belt /|/|/| pattern.
There is a sensor that reads this to calculate where toner should go.
You can force recalibration by removing and reinserting...
What I don't understand is the reasoning behind it.
All of the traditional PM parts are those that wear/tear through friction (Rollers/Fuser/Belt)
How does an oscilating light and some mirrors...
Unfortunately, not for this model.
It should be very similar as the CLX-6260FW and SL-C1860FW in design I believe (i think it also uses the JC96-06514A?). You can view the transfer belt by...