Nope. At the most reset the count for the transfer roller for the smaller machines (554 and below, 658 and below, etc), since they come with the transfer belt and will be replaced based off of that...
Type: Posts; User: tmmdmmm
Nope. At the most reset the count for the transfer roller for the smaller machines (554 and below, 658 and below, etc), since they come with the transfer belt and will be replaced based off of that...
I believe this is one motor that rotates regardless of B/W or Color. Makes more sense if its connected to Color Drums or Dev drive
I've been "retired" but stalking for a year now. This drove me crazy for a while, but the registration sensor right above the transfer roller caused 32-05 codes *Even though* it is not mentioned in...
I asked one of my old tech buddies the other day if there was any update to this since I retired, doesn't look like it.
Most of these CPU and SB issues were software related IMO, so if he got it...
Check the bypass. If the bypass jams or has a lift error its two oneway gears and the shaft they sit on (3 items total) in the T2/Bypass drive section. They rotate/grab opposite from each other, so...
Dog earing pushes me away from this, but first thing I do out of those LCCs is push in the lower right door while feeding to see if it fixes it. Takes a few seconds, and if it isn't the mylar its...
Can confirm. Not US market and cannot access Service Manual
BUT
for the c250i it does point towards the power supply cooling fan.
Check connectors, then replace fan, then replace EXCB, then...
Looks like PRCB, then. You might be able to find a used prcb that will work, the process was fairly straight forward if you go through that document that was linked.
Like I said, I never had to...
Sounds good, and I missed your earlier question. FRB can be swapped with a used board with no issues. PRCB on those machines do have a replacement guide in the service manual that you really should...
CL4 goes to the FRB behind the waste box, then goes to the PRCB.
Thats a lot of boards to try replacing. First thing I would do is reseat CN8 on the FRB, CN3 on the FRB, and CN9 on the PRCB. See...
Start by doing diagnostics, hold down the sub power button while flipping the main power on.
Last time I had an i-series rebotting both CPU and Storage board showed NG in this boot diagnostics....
This isn't much help but I don't recall load checks being able to help much with clutches. All it does is supply power clicking them on and off, which doesn't help with determining their strength,...
Pinched/Cut wire to the registration unit? Only time I've heard a click and black has been a short to ground. Unplugging power to the Front board like you did would get rid of that short. Plug the...
Windows or Mac? Prior to copy repair I was doing IT for a school district. Would set up a mac per class and CCC (Carbon Copy Cloner) to the rest with no issues using target disk mode. This was 2017ish
[/LIST]
IMO, this is the one issue where swapping with a used registration from a known good will not work well, so I'd cross that off your list of things done. Those bushings being worn may work...
It is possible but it depends on how you value your time. First time doing it I'd plan for about 2 hours, even though realistically it shouldn't take more than one. Its not terrible, but for a...
At the very least, techs seem to forget the platen glass has all the measurements they need. Just mark them on a piece of paper
You waited until after I left the industry to post this one?!?!?!?!
If I had any repeat offenders after cleaning the HV contacts I'd vacuum out the entire toner vent, replace any Belt/IU/Drum/Dev near life and drop Cyan TCR Level Setting to 0, it was the only way to...
As someone who almost exclusively works on Konica Minolta and KIPs, I felt it most fitting to post this here.
I am "retiring" from the industry. I've only worked in it for a few years, but the...
Is it similar to a coil whine? 454s had this issue, a board on the upper rear of the machine. I suspect because they were initially designed for 20a but then dropped to 15a, as it only affected the...
Need to steal this one
Second this. J9901 and 3003 are usually reg bushings and clutch on these models and occur more frequently out of Tray 1. Other trays usually have enough force carrying it by the time it reaches...
Had something similar a few months back. Machine would boot up until the scanner lamp powered up, then would immediately short out and go dark.
Try powering it up with all doors open, this will...
Did they send an example that you can share?
What happens if they scan greyscale instead of color? I've seen color lines pop up when copying from the DF but not while in greyscale. Ended up being...