Greetings everyone
Not sure if this is the correct forum for this question but it look like the Connectivity forum is more about general networking stuff.
Anyhow, I have a customer that has...
Type: Posts; User: green4go
Greetings everyone
Not sure if this is the correct forum for this question but it look like the Connectivity forum is more about general networking stuff.
Anyhow, I have a customer that has...
Thanks for the answer. I wish the documentation was a bit more helpful.
Have a Happy New Year everyone
Happy Holidays everyone
I am working with IC Link and I see a check box from "Wise Core Printer". I cannot find any information about it. I'm thinking its a generation (controller version or...
Greetings everyone
Is there a way you can lock down the address books so only administrators on a Canon IR-ADV C5850i with out using the Address Book PIN?
Thanks
Thank You for the reply. I will try see where the calls for the macros come from.
Thanks again
Late update.
The issue on this one was a VPN connection. The device was on a network that had to go through a vpn to another network before it can reach out to Uniflow server. when the network...
Greetings
Does anyone know if you can transfer overlay data from one kyocera printer to a newer Kyocera printer? Can you just take the SD card from the Current one and install it in the new one?...
This is a Canon imagerunner Advance DX C3826i.
If I boot the device up in MEAP safe mode, the device boots to the Home screen in the normal amount of time. When you boot to Uniflow, thats when it...
Greetings
Not sure if this is the right place for this question. We have a customer that run UniFlow online on their copier. when you start or wake the device from sleep, sometimes the control...
I know have 4 Ecosys M & P devices (brand new. less then a month in the filed) that have this behavior. It don't matter the recovery mode, you have to turn Off and On before it will print. I have...
These are connected to LAN only.
Greetings All
I have 2 brand new Ecosys PA4500x that will not wake from sleep. printing jobs just stay in the queue until you turn the device off and back on. tried changing the sleep settings...
We setup our devices with WSD Scan & Print turned off (Enhanced WSD needed by network fax drivers). however, one small city that replace all their devices with Kyocera started having random printers...
Are you trying to get to Service mode or the System menu?
if you are trying to get to service modes - try "status" button then 10871087.
if you are trying to get to System menu - try either UN:...
Thanks for the response.
I sent that link to the person i was trying to help.
Thanks again
Greetings everyone
Does anyone know if Canon has a utility that can create an .msi file? I found the Canon Driver Configuration tool, and was able to create driver profile. however, i could not...
If your dealer have KFS, you can register the devices on KFS then update the firmware that way.
If you can't get IE or Edge to bring up the Command center RX, you can use Kyocera Netviewer to make the security setting.
Good luck
you can always go to system menu and use the device login from the panel and reset the Admin account password from there. or create another admin login. that should allow you to get to the CCRX.
Thank You for the help
Hello everyone
This Primelink 9065 with a EX-i Fiery take about 5 minutes to connect to CWS or to the print driver first thing in the morning. You can still get to the web-interface, but takes a...
Hi All
I call Kyocera tech support to get information why the TA XXX4 devices are real slow when you select a destination in the Send mode. The answer i got was that this was an upgrade in the...
Thank you. Got it going now
Greetings
I have a Canon DR-G2090 that has nothing on the display. I can still see the scanner when i open CaptureOnTouch but will not pick up the paper. does anyone have instruction on how to...
If you have FMA central 4.4 or older the require you upgrade to 4.5
Good luck