Hi Chaps,
So indeed turns out it was the old transfer belt unit that was the culprit, this is what was causing the dotted line in the first place, and upon fitting a new drum on first visit all I...
Type: Posts; User: LiamXCIII
Hi Chaps,
So indeed turns out it was the old transfer belt unit that was the culprit, this is what was causing the dotted line in the first place, and upon fitting a new drum on first visit all I...
Okey dokey, I will order up a new drum and transfer belt unit and fit as a pair, hopefully this will cure this horrible dotted line! :D
Thanks for confirming this, so what I have potentially done then, is...... fit a brand new drum unit, in which has now become faulty because the 2nd transfer belt unit has just taken it out again....
Hiya,
Thanks for replying, did you get a chance to see the example of the problem I attached, does the fault you describe the fix for match that?
If so, then I will re order drum and transfer...
Hi everyone, here is one for you all.
I have a Taskalfa 9003i, which has done about 2.6Mil prints so far, creating vertical black dots in a line across the paper.
At first glance I thought...
This device only has a cassette 1 which has a 250 capacity. The optional cassettes for these devices are of a different specification allowing 500 capacity.
So I tried changing the paper side...
So after much digging around we were never able to fix the device!
The device was pulled out to be worked on in the workshop and the below list of parts were fitted to try to cure the problem.
...
The device recognizes A4 when the dial is set to A4 just fine, I'm not getting the message "Load cassette 1" instead it's a message that says "Error occurred at cassette1".
The message only...
Hi guys,
I've got a TA351ci (Basically a copier version of a P6035) with an error at cassette 1 coming up.
Now I've seen the message in the past about "Load cassette 1" a few times which can...
I moved the device to a different location to work on it, tried a different kettle lead too, same problem occurs.
Will have another crack at it tomorrow now the device is in the workshop. Will try...
Image appears normal between inch wide bands, the first band is solid black followed by an immediate two-tone band, starting white gradually getting darker.
I'd say the band is a good inch wide
Thanks Blackcat,
Sorry I should have said Imaging unit as a whole, I took out the entire lump from one device to this, so that included the Dev unit, Drum unit and toner cartridge aha 0_o
Hehe, have you tried turning your crystal ball off and on again :P lol!
Meter of device is 165,000
Same goes for Maintenance kit
I had a spare printer of the same, so was able to rob some...
Hiya,
Anybody seen this type of fault before on a Ecosys M3655idn? MFD version of a P3145dn
Inch wide black bands down prints.
Image attached
I don't believe it to be US as the one I was working on was here in the UK and the customer has 20 of them dotted about the place. In terms of release date I am unsure but if it helps the one that I...
Hiya chaps,
I looked at the white arm that comes down to meet the paper when the cassette is pushed into the device, and this was indeed bent upwards too far, a little bending down and it seems to...
Thank you, I shall give that a try and get back to you on my findings :)
Heya, it displays the correct paper size onscreen.
So I know the switch with the 3 flags that determines the paper size specified on the dial on the tray is ok.
And no it's not a 3551ci its a...
Hiya all,
I've got a TA351ci which is intermittently showing No paper in cassette 1 message on screen, usually when the paper in the tray gets low.
I have tried stretching out of the spring....
It's fairly easy to get to, best if you take the conveying unit off so you got more room to play with.
The solenoid sits directly under the ID sensor Assy and to get to it you want to take out...
Turns out the manual I was using was 4 versions too old!
Error 33 exists on the newer version and it relates to the ID Sensor Solenoid getting stuck.
After a clean it was working once more :)...
Hiya,
Unfortunately the old belt unit has a rip in it :/
Part of the reason I have replaced the belt unit, but it's failing belt initialize.
It's a bit poop that the error of 33 doesn't...
Hey All,
I am getting error code 33 after performing a Belt Initialize U469 on a TA8353ci
Unfortunately the error code does not exist in the manual... anybody know what this means?
My...
After a Clean in and around the transfer, drum&dev area, also a clean of the terminals and re plugging the connectors on the HVPS the fault is still there.
On a 1000 page run of A3 paper it...