One Stop is MUCH more logical!
Thanks for the tip!
:)
Type: Posts; User: FuserNoob
One Stop is MUCH more logical!
Thanks for the tip!
:)
Super!
Thanks very much!
KM's new 'knowledge base' is extremely frustrating. I cant find a parts manual for the DF704 and/or DF629.
I'm looking for a part number for the PS1 Document Empty Sensor flag
Thanks for any...
No, this an off lease unit that hasn't been updated who knows how long.
On other 4 series units i've updatd that had firmware older than K8 needed to get to that release before accepting M1.
...
I hope no one minds that I'm re-uping this thread..
I have a client with a C554e currently on A5C10Y0-F000-G00-J5(DB), which I'm not familiar with and cant find a reference to on One Stop.
Can...
No Problem, MarioTech!
I'm in exactly the same boat and feel your pain!
Here's the latest FW:
Version GCP-Y2 Function Version 4.2 https://onyxweb.mykonicaminolta.com/OneStopProductSupport/images/new.png
1/2/2024 ...
Most of the KM machines I service are off lease, and I have had the same experience with FW updates that you describe. This machine is on, what i assume is, the factory release G00-G3 from 2015...
Exactly what I needed! THANKS!!
Yes, i wend throught the proper FW update procedure. I tried to apply the GCM-X4, but it just paused at the 2nd pillar then booted as normal. Which is why I started looking for intermediates.
I tried to apply the GCM-X4, but it just paused at the 2nd pillar then booted as normal. Which is why I started looking for intermediates.
Hi all!
I have a customer with a C368 on firmware G00-G3.
It (obviously) wouldn't take -X4 and as I was looking at intermediate steps came across 'Special Firmware GXX-A2'.
The next step from...
They are the same length, the difference is in the compression resistance. The 'thin paper' version is lighter tension.
I have a C458 and was giving a 20-02 error on tray 2 - I replaced the pickup/feed rollers, no go, clutches and torque limiter, no go, replaced mag clutch, no go, replaced the spring as described...
Good call!
Thanks for the update
My other thought is to use the 'if it aint broke, dont fix it' method, as the reason for the FW update is procedural rather than to cure an issue.
Yeah...I thought of that as well.
Might as well give it a shot at this point.
Thanks
The jump drives are 16gb
Bizhub Secure in NOT on
OK...update
No go with updating individual components either. Still getting the same errors, NG, NG and hang at 10%
Any other thoughts?
Thanks
I prepaired individual USB drives with G00-W5, GCD-Y1, GCF-Y1 and GCK-Y2 as stepping stones to GCM-Y2.
I got onsite and tried the first step, G00-W5, and had the same issue:
MFP = NG
ADF = NG...
Thaks for confirming what i was planning to do! I appreciate the confidence boost!
Hi All,
I have a client with 4-C458's
All 4 were on G00-R9 and I was able to update 3 of them to GCM-Y2.
On the 4th machine I got the following results:
MFP Controller - download NG
ADF...
Thanks for that! I can always use a new resource!
I've been using this one for error code information:
Error Codes > Konica-Minolta > page 1
Hi Folks,
I have a client that runs a photo booth using a Mitsubishi CP 9550 DW Die Sublimation printer.
This one is new to me and there arent a lot of techincal helps on the ol' interwebs.
It...
Thanks ltdiniz!
That did the trick!