Search:

Well it did it, I'm on fucntion version 7 now. Out of curiosity I got to ask, there is an auto update setting requiring a proxy and a username plus password, was wondering if thats to connect her to...

I don't think so, if I'm right the bit value should be 01100000 , found on YouTube, one guy did it. Question is if I can just switch it from 3 to 7 and not 3 to 4, then 5 and then 7. I wouldn't want...

Alright cool so Switch 25 and the hex value is 60, what about thr bit value?

So I got to ask straight up, since she is the normal C224 flashed to become the E model and is currently on Firmware Version 3 can I just update it to Version 5 and then 7? if thats the case I will...

Apologies for the late reply but I thought I fixed it, the firmware is Version 3, it happened again today same situation the blue lights are blinking, I did check the "job list" and it was blank so...

Is it all of them or just some?, she never had any issues when I sent stuff from Windows...not mentioning even the fact I'm on windows 11 Beta Insider, weird how its just on mobile 🤔

Honestly I'm wondering if this is not due to that "System Error" She got before she got to service, it happened when she was sleeping, same thing it didn't print, then went to sleep and I just heard...

Hello gents, my C224 flashed to E model has returned from official service finally duplexing works (Hooray!) Recently been having problems with her printing while she's in sleep mode.The blue lights...

Will do so, will try to clean the duplex sensor aswell, also found out the one of the screws that holds the plastic on the exterior has been stripped so someones been definitely trying to get into...

I used 4 straps of electric tape and no luck, 32 05 still and same situation, prints from both sides the first one, second comes in one side and gets jammed like in the very first picture

Should I...

Got 4 pieces of electrical tape in that area, hope this works lol55865

So I didn't have to take it out? 😂
My bad, putting it back wont be too hard since I did it before with an older model already for cleaning. So a thicker sticker will solve the problem most likely ?...

Alright got it out, I don't have any panel stickers though, what could I stick on there? one of those sponge items for putting under the feet of chairs or something thinner?

I think we both were mistaken, the exit area is in the upper side of the machine, here there is a solenoid as indicated per the service manual I found which I attached below
The part which I took...

So in here then?, is this not the one for detecting paper from the bypass tray ?

Is it under the metal cover here?, I don't see it there

Tried it didn't work, infact no tabs are broken , both are present on the door and on the machine same with the item that has the "M6" sticker on it, the upper latch on the M6 never engaged with...

Alright will try using a few stickers of some sort, is that solenoid located on the door or inside the machine towards the left? While I'm there I will try to make the two latches close properly,...

Founds some more information online, that said it could be the motors but I have my doubts unless the belts just gets stretched and possible can't turn the other gear, I would bet my cash on a...

Here is the code..32-05, also noticed the plastic down below has been cracked, I'm starting to wonder if I just got mine made on a Friday evening or if someone's been in here already, to add, the...

I sent 3 photos to do in duplex it did it fine so It seems it cannot print anything after the 3rd picture, alright so what should I take apart?, the fuser and look out for dust covered sensor perhaps...

My 224 flashed to e can't print more than 1 sheet of paper of images before getting jammed. I printed 10 pages of normal text with duplex so 5 pages in total with text on both sides without a...

Well it worked...kind of since the ping now works but I cant log onto page scope, tried even using a different IP address but I'm getting a new error now called " Data Transfer Interrupted", any clue...

My C224 model, with firmware successfully upgraded to become the "e" model still cannot send scans to my Gmail. I followed all guied and decided to ping test her, it states "ping failed", I have...

It works for you?, I have everything set and it today got updated to become the "E" model, version 3 installed, still it states "server connection error".