THANKSSSSSS ;)
I will test it this week-end and with a bit of luck it will work.
I come back to you quickly.
Thanks
Type: Posts; User: costou
THANKSSSSSS ;)
I will test it this week-end and with a bit of luck it will work.
I come back to you quickly.
Thanks
You're right, normaly face up option is in The advanced Tab.
I checked with PCL an PS driver and Not.
I installed Xerox 4110 PS drivers for test.
The Face up option appear in Advanced Tab...
Yes i tried, but print face down.
Maybe i have to reload software or firmware
Software Version :
Version 1.211.1
Any NVM to change ?
Hi,
Directly by the printer screen or the web interface ?
Tell me the way to go
thanks
Thanks for amswer,
i looked everywhere.... No tab Finishing or Output.
I tried PS and PCL Drivers
I also Tried 4110 drivers with face up option but still printing face down
Hi,
I have two Xerox 4112 CP.
I can't send a print Job with face up... i can do it in copy mode.
I don't understand i have used all off drivers model.
With my old Xerox 4110 it was...
nobody to help me ? please....
Hi,
here is my story.
I have a DC700 with tray 5.
I always have a jam as seen in the photo.
Yes only for reload machine
I need to setup system regitration.
i donīt have pws and software download tool but i have edocs
how can do to have it ?
HI,
On my dc242 when i go to pws mode ( hold "0" 5sec + green touch ) , i enter password 6789 and it freeze !!!
i canīt confirm it
i have to reboot the printer to test again. i can enter in...
Hi,
I have a profesional finisher plugged to a DC260 with built in fiery.
I have two Problem :
- When i send a print job from my pc or directly in the CWS the printer print 4 sheets, then...
Hi,
I need to enter on service mode with my Colorqube 9303 to do some test patern and print Head verification but i donīt have the password.
I did not have diagnostic software. it's required?
...
thanks but i resolved it.
finally it was the toner.
i had toner compatible. i put an original toner magenta, and after 100 prints, it disappear....
so now i have to change the 2 other toner black...
Hello, i have exactly the same problem like you, but for me it's in black and magenta only. not in cyan or yellow. i join the 2 scan of the black and magenta print.
2066120662
i put a new cartridge...
thanks for your answer.
1) cable seems to be ok, i flip it, and the same
3) i reset all the NVM, and it's the same
2)i'm searching the soft to reinstall it, when i find it, i will say to you what...
Hello,
I have a DC242 with fiery controller, when I print something from a computer or sending directly something from the fiery, i have a problem like you can see in the 3 photos.
I intempt to...
Hello,
in my xerox 2060, I have error 10-382, i change with a new fuser cleaning web, but still happen the error code.
I think I have to change a NVM, I saw in one topic that is the NVM 744-042...
thanks, but i'm very sorry, i don't know what is it or where is it in the machine . Can you help me to find it in the machine ?
Hello,
i have 1 xerox DC460st, and when I start the machine, it say :
"please wait, machine test in process" then
"adjustments are in progress" then
"system is warming up. it will be...
Hello,
i live in spain, and i search to buy a fuser heat roll for DC2060.
Ref. 059k59910 or 059k10680 (i donīt know the difference of each one)
If you sell that, thanks to send an email at :...
hello,
as I have a problem with my DC2060, there is 2 days, i reinstalled all the creo with no problem, but my problem original still happen, anyway....
Today, I intented to swap 2 disc SCSI to...
now I have interchanged the 2 boards on the DC2060, and still happen, exactly the same.
hello,
I changed the RAM on the Creo, and the problem still happen , exactly the same...
if you have other idea...
thanks