Paper jams in registration rollers on arrival or 1/8" leading edge pass it.
Jams from tray 1, 2 and by pass at the same location.
Printer has 160k prints
The sensor actuator moves freely.
Check...
Type: Posts; User: gideon
Paper jams in registration rollers on arrival or 1/8" leading edge pass it.
Jams from tray 1, 2 and by pass at the same location.
Printer has 160k prints
The sensor actuator moves freely.
Check...
The customer complain for a noisy printer. It is just laboring harder then usual with 150K prints.
I run successfully the fan - no noise.
I tried to execute dc330 071-001/2/3 the main motor...
I have the parts book
I need a Toshiba 2505AC Cyan developer (all unit or parts by order) and a cyan drum.
Parts number available, I need a regular phone number for Toshiba parts.
Thanks
No margin problem. Symptoms like developer blade clogged, striking white line on left and right sides of the page.
Cyan leaves void lines on both sides of the page.n
I replaced the drum unit OEM, the LED cable assembly, the LED assembly, still void line.
I guess the only other option is to replace the PCB.
...
Thanks for all this info, the symptoms at my customer's printer are different but it help to explain to him that it is not an easy solution and may take some time (and money) if he wants to fix it.
I have the manual.
No paper in the fuser or on transfer belt. The paper stops sometimes in front of the registration roller.
The registration rollers turn fine and the flag looks fine. Can be the...
Attached some registration adjustment. Function 45.
The print mode is fine and crispy, the copy is too light even if I take it out of auto to manual and darkening the exposure.
Is there anywhere in the SP mode that the exposure can be adjusted?
I...
Thanks a million, that will work.
Is the DP 2310 drum and blade replacement are the same procedure as the DP 2000/2500/3000?
I have the manual for the DP2000.
Thanks in advance
On start up I get the pagewide screen and then it turn to all blue screen with the number 8B380001.
This error is not in my manual, any idea?
I removed the scanner and disconnect the cords from the main board, upon reassembly I get the message "replace cartridges".
The printbar doesn't lift up to lock the cap.
Any idea?
The customer is using Xerox toner.
imaging unit looks okay and has half life left.
The change in quality was rapid.
I have the manual but if you experience anything like this it will save...
I have the manual
I replaced the fuser drive assembly and now get the error 57.07.
The fan 3 is turning fine when I turn on the printer (both fan under the cartridges turning fine).
The...
Did anyone try to put a simplex fuser drive assembly?
It is a duplex printer.
Check the attachment below.
Firmware updated.
Reset to factory.
Any idea?
The colors registration is not in line with the black registration, the colors are above the black.
Different cartridges didn't help.
Calibration didn't help.
Transfer belt sensor was cleaned,...
I sent it to your email, let me know if you didn't get it.
Make sure that you install the right firmware, yellow or red dot by the lens are different firmware.
Sorry for my tardiness, it was error 51.20
Anyone have old or new ADF hinge for the D660 D760 D860 series?
Part number FC5-0011-000
Thanks
Thanks for your help guys.
The error is E061 (even when the display shows Letter-R in the tray).
Conclusion:
I call Toshiba tech support with his help I Change 08 - 4542 from 0 to 1 (disabling...
Paper jam Letter-R from tray 1 and 2 when the paper reach the fuser. The registration of the print on the paper is in the correct position.
Install new fuser.
LCT Letter - no jam
Tray 2 is legal...
I have the manual and check the control panel connection and cable and all connection on main PCB.
The display of Brother comes on and the screen going blank and error OE comes on.
No motor...