You can reload the contents to the SD card with a disk image application. I have the SD image available.
Type: Posts; User: Detonation
You can reload the contents to the SD card with a disk image application. I have the SD image available.
I am assuming that would be because copies are multiplying your color imbalances. So if your print has slightly too much cyan (something hardly noticeable), and you make a copy, that copy will have...
The original SSD in the machine was 128 GB. I tried replacing with a SSD of 120 GB, no luck. Now I have tried a 250 GB HDD, and the machine does (special) Altboot. Maybe early versions of the machine...
I tried special Altboot with version 119.009.023.13000. As I cannot perform PWS altboot, I am hesitant to format HDD. If it doesn't work, I am stuck without a working machine.
I have a AltaLink C8130 running 114 software which is running fine, but refusing any sort of software upgrade or Altboot.
USB port are enabled
software upgrade is set to allowed
I was able...
I have only seen the purple drums over here in Europe. I do remember the 7345 drums used to be blue, and the 7435 drums were green (as were the DocuColor 252 drums), but the newer batches of those...
Thanks for sharing that, good info!
I would second that, have seen some good machine with 4 million clicks. That being said, make sure the service log is with the machine. Replacing parts is expensive. If just the finisher is the...
Performing forced Altboot won't hurt, but I don't think it will solve your problem.
As far as I know there is no way to adjust the belt on the 7232.
It is pretty common for the sensor to become dirty, as it is, inconveniently enough, located under the belt.
There is a reflective patch (square shiny sticker) on the belt that passes a sensor. When the patch is damaged or the sensor is dirty, you will get this error. Since the patch is on the outside of...
Interesting, this is not a setting I have ever heard of before. Subscribed.
You can login to diagnostics by holding the 0 key for 7 seconds, and while holding it, pressing the start key. You can then login as service admin with 6789.
If you go to tools => diagnostics, you...
Have your tried the Bypass chute assembly? Also, by pre register, do you mean pre-registration sensor, or pre-registration motor?
Appreciated! I do have plenty of C8030-C8035 to use as a source though, it's just that it hasn't worked up to now. I'll retry when I have time.
There is no setting I am aware of the would enhance gloss. You could, at your own risk, set the paper weight to something heavier than it actually is. This will slow down printer speed, up the fuser...
C8030. But I’ll try again some day.
Sent from my iPhone using Tapatalk
Thanks for sharing that diagram! Now, as for restoring a corrupt SD, I have personally not been able just yet to clone a SD from another AltaLink.
Sent from my iPhone using Tapatalk
Also check drawer connection for bent pins and/or pieces of paper or debris
I've also seen these machine can be picky about the USB stick. Try a different USB stick as well, newly formatted FAT32. You can even try 2 USB sticks, 1 on the front and 1 in the back.
Well, there is even 'software_upgrade' in the file name. The altboot files have 'ALTBOOT' in the file name. The 119.xxx ALTBOOT files are 632MBs in size.
Yes likker Gaffers01 said, Impose is not a standard option, but you need to purchase a license.
On the 700 Fiery: is Acrobat in fact installed? If not, you'll need to reinstall. Do you have the...
I would guess the toner powder itself is the same as the 4110/4112 and D95/D110/D136, but am not 100% sure. Obviously, the cartridges and chips are different.
This link is for the upgrade, not for the full altboot.