Hello people
Any ideas about this error in accurio C3070?
I have already swap laser between colors.
I swap color registration sensor front rear
thanks for any help
Type: Posts; User: remati
Hello people
Any ideas about this error in accurio C3070?
I have already swap laser between colors.
I swap color registration sensor front rear
thanks for any help
Thanks for help
Yes I have all the licenses I need
-Copy
-Scan to file
-network print
no-color copy
-Scan to file in color
Dear friends
In a KIP 770 when pressing the scan color key to folder, nothing happens, it doesn't scan.
Does anyone have an idea of what it might be?
thanks all
Thanks for your serious response.
I think you are talking about M32 de-courl motor. Yes I have that note from KM and I had already saw the wiring from the motor to the ADUboard1.
Yesterday I...
Yes I have !
I have all manuals from KM
Thanks
Hello friends
-Several times a day, machine blocks with these codes
-First 0413 and after that C0020
For run again,needs to be unlocked by unplugging the wall plug and wait several minutes...
hello people
biz with the message in the display " insert tray "
and that refers to tray one in tha machine
any help??
thanks
thanks for your repplay ...DIGIman
it was a contact problem at the conection between process carriage and the machine
thanks again
hello
try that descripion
Description
C-3804 (C3804).
Solution
CAUSE: TEMS/4 has flipped or is out of position.
SOLUTION: Correct the position of the sensor.
hello people
I have that error in one Biz C8000 error when doing the color regist adjustement C-4522
I tried sensors
PRCB etc etc
but didnīt solve
if someone have any idea Iīll be...
hello
You could have a problem of Firmware nin my opinion you must in first refresh it
-----thanks for your reply
yes I had already tried everything ..new developer..and so on...and still have banding
thank you
Hello people
-About the problem "yellow banding" -any new ideia..? or something new..?
-I still have problems with this topic...
thanks a lot
you have to adjust the transfer in operator mode
goto the "process adjust" at the tray you have that issue and look to the menu ...go to tranfer adjust TRAIL edge
hello people
I have a biz C8000 that ssometimes a day falls the code 39-03 falls..
changed sensorīs changed ....fusing unit for another for teste ..and the same problem
any idea?
thanks in...
you must ask for all ..."cartridge assy" (A0G6R7A422)
that reference doesnīt exists...
sorry
Try change developer and developer unit....but normaly its solves to change only de developer..
Hello people
I have a biz 1051 that when we tourn ON the SW! "starting up the message stops and the start ,stops too
the key for low down energie shows orange blinking ...
Iīm trying to...
hello people..
I have a KM biz 1052. that sometimes ,in a print cicle the imagem "shifts" for the side about 5 or 6 mm..
In a run of 200 ~300 prints we may find 5 ,10 or 15 prints with a...
Hello people
I need help to find some PDF or other docīs ,where I can find an easy way to do installations of fiery controlers (and drivers/PPD konicaminolta)..on Mac hardware...
Someone help...
funcion version is something like the "generation of the firmware"
the newest version are version 5
and you must change a DSW in the machine
you must read de " Doc " ,that is sent with the...
Hello
yes...always update for the last version of "mass production"....and the newest date ...
Hello people
any ideia about this error..?
Upgrade firmware already done ....
mayde problems with HDD??
thanks all
...
is very difficult to replace and it is not advisable to do that..but its possivel,and have reference..
--Any idea about this error code...?
thanks people