Search:

Hi guys,
I know that nothing from developer -belt assy on 6027 is spared but it looks like rebadged IOT. Do you know who is the origin of this... machine? Probably they have a spared parts for it....

Dirty with toner built up primary transfer rollers. If cleaning looks like a job - just replace the transfer belt assy.

Can you print a page, is it blank?
Reset NVMs - printer -copier -IOT-All! Try to check if the drum is turning! Cheat the front and side doors and turn the drum - dc330 93-045. Move the drum and...

Hi,
Is there someone to know workaround to install Wide Format Scan Services-WFSS for 6204-controller or 6604 in Win10 OS. Actually any application that can take scan from Xerox Wide Format...

check if the paper size switch board (behind the tray) is not dislodged, like a wild guess check also bypass to be set to letter, default paper is letter, default units are inches and no sim is...

this is low voltage power supply. noisy machine is covered by warranty. meanwhile try to set power save on scheduled, 8h-17h for example.

Check first if CR16 is light on on IOT board (Top, Left). If it is check on F1 or PJ27 pins1,2 for true 24v. If CR16 is off or 24v are below 23.2v unplug HVPS from IOT and power again! if it doesn't...

Remaining packaging, front (green marked) latch should be lowered, micro switch below the cartridge (stapler) or just load the old one!

if you have a Eureka check the tip number 907532..

I am not sure but it looks like a gateway or security problem. You can check the server driver or reload the software as well. A network problem should be considered first!

-Adjustment-DC301-Engine-System reset ( or/and same for the controller) before to go any further.

604K45000 or 604K45001 is the kit to repair the IBT patches (2 on the belt). The root cause usually is the cleaning blade seal on the front side. Check Your new Edoc for DC330- 091-005 to run the IBT...

There are 2 latches on the IBT assembly and of them is not in position. Looking at Your TP it should be the one of the rear side. You can refer to PL6.2 item7 and to gain access You can use the left...

Check the photo atached in Eureka Doc#1052667!

Disable your 802.1X authentication and You will be OK. Use Tools - network settings on the UI (or WEB)!

Go to "Diagnostic", scroll to HFSI and appropriate item subsequently! use "ok" to confirm.

There are few possibilities but depending what you wrote, it looks like your CCD PWB has "back loop" ballast resistors burnt out(5v gen.). Original ones -3x 10 ohms 0.125w should be replaced by 0.5w...

Maybe You have LDAP set already. Mark that local Address book is not default one and appear like "internal". The cust. have to switch it manually that is a high intellectual effort. The work around...

imaging unit have a "first time " 80ma fuse. I didn't find reference but usualy it is a fast blowing fuse easy to find in internet or a local electronic store. You can find it on the right bottom...

For 3600 keep in hand some PL1.3 belt transport -'item 48 ELA unit 3x5' and
solenoids are prone to stick in actuated position for apparently no reason-
just shim the pad (rise it) to keep them...

in service mode nvm read/write


744-006
Fuser Standby Lamp ON Temp
45
0~99
1 deg.C
Nominal=175 deg.C

Press 0 for 5" and press start (0 still pressed),
6789 in log ,
machine status (blue buttons),
Tools,
System settings ,
common setings,
Maintanance & diagnostic,
NVM read/write.
put...

make a cheater. 3-11-13 pin shorted on 15 pin connector (PJ151 on LVPS i think) remplace OCT. If you still get error The IOT PWB is suspected. THere is a post in this forum about the cheater. PN is...

did you find it? If you are still interested make me know!

Try to unplug the HDD and boot it again. If it cycle boot again, switch off, unplug the battery on CN29 and short the pins on main board. After 20" plug the battery. When the boot is OK perform...