needs to be email program loaded on pc/server like outlook(MAPI compliant) . GMAIL is web based. also you can try mapi4gmail.com,
Type: Posts; User: faxman28
needs to be email program loaded on pc/server like outlook(MAPI compliant) . GMAIL is web based. also you can try mapi4gmail.com,
needs to be email software like Outlook (MAPI compliant) not web based like Gmail. You can install Outlook and have Outlook access Gmail.
check out MAPI for GMAIL , just saw it on web, ...
Also check sim 22-10 to see what type of finisher the 4111n has connected, the other item in the user guide mentions that 2-sided mode has to be working(see below). also check the saddle stich...
go to operation settings home screen settings background image. can only be set via web page
H2-01 is open thermistor on lower roller(pressure roller).
Thermistor is bad, put you said you replaced, check resistance of thermistor , with meter, usually in the 30 to 70k ohm range, compare...
if your talking about the password message , that is normal the file will print, if your trying to print pdf from a mac on a usb stick, and it doesn't print with password message on screen, the user...
torque limiter is sticking not allowing sep roller(bottom roller) to turn causing the start of a flat spot, if these mfps don't have a high page count you might want to try the original rollers,...
oem drum ? oem toner ? also are you doing calibration, 46-24 or 46-74. there is a density sensor that sits in transfer roller unit that reads patches on drum. your pic just shows front side of drum...
TT-051915_3
sim 67-33 set A to Q to default value of 128 then do complete calibration
I would look at toner hopper, these mfp's you can change toner on the fly(mfp does not stop when toner cart is empty). toner sensors are in toner hopper. also when machine is first setup, after 25-2,...
check/replace torque limiters, one-way bearing and shaft for lifting/dropping of pick roller. I think there is a belt tightening procedure for gear on adf drive unit for the gear that drives the...
sim 46-19 set to 1 instead of 2, adjustment 12 I think in adjustment chapter in manual, also 46-74 calibration, and if all else, set text as default for exposure.
The dev units have chip and can't be swapped unless you swap out the the wire harness on dev units.
do adjustment 3 from the adjustment section of the service manual, this adjusts the registration/process control sensors for the transfer belt.
check the wiring from power switch pwb to lsu mother pwb,
you need to be a Sharp authorized dealer, and have to contact tech support, "product key" are normally generated by Sharp corp in Japan. The directions that are in the posted pdf has not been...
Below is from the mxm503n series SM page 4-3
Toner density control reference value
setting
This adjustment is needed in the following situations:
* When developer is replaced.
NOTE: Be sure...
run the copier with finisher disconnected(don't forget to remove dummy punch and mounting bracket to free up shifter) to determine if finisher is problem . when the jam happens there is no paper in...
Also on most mfp's with hdd print jobs are processed thru the HDD, so print data remains on the drive, seen this first hand many years ago . going to U.S. state department when in engineering support...
depending on your customer and the nature of the data on the hdd, there is a end of lease function that can be accessed through the web page , it does a DOD wipe of the hdd and I think it clears all...
check the gears on toner cart, used to get some toners were gear popped off and couldn't get it to stay on shaft. is toner coming out of cartridge.
The thicker seals on the waste toner boxes definitely help,(a lot less toner on top of the dev units) along with the updated charge units/drum units. I only see dev pull on very low volume color or...
problem is probably caused by voltage, the Australian power is 230v at 50hz and the 4110 in US is 125v 60 hz and 20 amp,
does it see the original as inch size when placed in ADF ? country code...
These settings should work , it is a bulletin or tech tip from Sharp , have used these settings when the mfp has nervous break down. Also check the process sensor(or what ever sharp calls it) it...
the hdd raw copy works well, If you copy an sd card from a customers machine , all their programing will be on the "bad copier (from experience). you will have to delete all scan settings, network...